John Deere Engines Fault Codes List: 000676.05 to SPN 1075 FMI 2
Page 2 of 17 of the full John Deere Engines fault code list (1,853 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.
John Deere Engines codes 000676.05 to SPN 1075 FMI 2
- 000676.05Glow Plug Relay
- 000729.03Inlet Air Heater #1 Error
- 000729.05Inlet Air Heater #1 Failure
- 000833.02Rack Position Sensor Error
- 000833.03Rack Position Sensor Voltage High
- 000833.04Rack Position Sensor Voltage Low
- 000834.02Rack Actuator Error
- 000834.03Rack Actuator Voltage High
- 000834.05Rack Actuator Open
- 000834.06Rack Actuator Grounded
- 000834.07Rack Actuator Position Error
- 000970.02Auxiliary Engine Shutdown Switch Signal Invalid
- 000970.11External Engine Protection Shutdown Switch Signal Active
- 000970.31Auxiliary Engine Shutdown Switch Signal Invalid
- 000971.31Engine Derate Switch Signal Active
- 001041.02Start Signal Indicator Failure
- 001041.03Start Signal Indicator Active
- 001075.06Fuel Transfer Pump Current High or Grounded Circuit (Racor Fuel Pump Only)
- 001075.12Fuel Transfer Pump Failure (Racor Fuel Pump Only)
- 001076.00Fuel Injection Pump Control Error
- 001076.01Fuel Injection Pump Control Error
- 001076.02Fuel Injection Pump Control Error
- 001076.03Fuel Injection Pump Control Error
- 001076.05Fuel Injection Pump Control Error
- 001076.06Fuel Injection Pump Control Error
- 001076.07Fuel Injection Pump Control Error
- 001076.10Fuel Injection Pump Control Error
- 001076.13Fuel Injection Pump Control Error
- 001077.07Fuel Injection Pump Controller
- 001077.11Fuel Injection Pump Controller
- 001077.12Fuel Injection Pump Controller
- 001077.19Fuel Injection Pump Controller
- 001077.31Fuel Injection Pump Controller
- 001078.07Fuel Injection Pump Speed/Position Sensor Error
- 001078.11Fuel Injection Pump Speed/Position Sensor Error
- 001078.31Fuel Injection Pump Speed/Position Sensor Failure
- 001079.03Sensor Supply Voltage 3 Out of Range High
- 001079.04Sensor Supply Voltage 3 Out of Range Low
- 001080.03Fuel Rail Pressure Sensor Supply Voltage 2 Out of Range High
- 001080.04Fuel Rail Pressure Sensor Supply Voltage 2 Out of Range Low
- 001109.31Engine Not Available or Condition Exists
- 001110.31Engine Not Available or Condition Exists
- 001347.05Fuel Pump Pressurizing Assembly #1 Sensor Circuit Open, Shorted to Ground, or Overloaded
- 001347.07Fuel Pump Assembly #1 Rail Pressure Control Mismatch
- 001347.10Fuel Pump Assembly #1 Fuel Flow Low
- 001348.05Fuel Pump Pressurizing Assembly #2 Sensor Circuit Open, Shorted to Ground, or Overloaded
- 001348.10Fuel Pump Assembly #2 Fuel Flow Low
- 001485.02ECU Main Relay Pump Error
- 001569.31Engine Protection Derate
- 001639.01ECU Detects Zero Fan Speed
- 001639.16ECU Detects High Fan Speed
- 001639.18ECU Detects Low Fan Speed
- 002000.06Fuel Injection Pump Control Valve Error
- 002000.13Security Violation Controller Not Installed
- 002005.09No CAN Message From Source 5
- 002030.09No CAN Message From Source 49
- 002071.09No CAN Message From Source 71
- 003509.03Sensor Supply Voltage 1 High
- 003509.04Sensor Supply Voltage 1 Low
- FMI 2240 FMI 9No CAN Message Received From Source Address 240
- FMI T10PWM Throttle Abnormal Pulse Width
- FMI T11Excavator Throttle Reference Voltage High
- FMI T12Excavator Throttle Reference Voltage Low
- FMI T13Excavator Throttle Ground Voltage High
- FMI T14Excavator Throttle Ground Voltage Low
- FMI T15Excavator Throttle Input Voltage High
- FMI T16Excavator Throttle Input Voltage Low
- FMI T22Analog Throttle (A) Input Voltage Out of Range
- FMI T23Multi-State Throttle Input Voltage Out of Range
- FMI T7CAN Throttle Invalid
- FMI T8PWM Throttle Input High
- FMI T9PWM Throttle Input Low
- FPN 1550 FMI 5Air Conditioner Compressor Current Low
- FPN 656 FMI 5Injector #6 Circuit Has High Resistance
- FPN 656 FMI 6Injector #6 Circuit Has Low Resistance
- SPM 2659 FMI 3EGR Flow Signal Out of Range High
- SPM 97 FMI 31Water in Fuel Detected
- SPM T8PWM Throttle Input High
- SPN 100 FMIEngine Crankcase Pressure Extremely High
- SPN 100 FMI 16Engine Oil Pressure High, Moderately Severe Level
- SPN 100 FMI 2Engine Oil Pressure is not Zero with Engine Stopped
- SPN 100 FMI 31Engine Oil Pressure is not Zero with Engine Stopped
- SPN 101Engine Crankcase Pressure Extremely High
- SPN 101 FMI 16Engine Crankcase Pressure Moderately High
- SPN 101 FMI 3Engine Crankcase Pressure Signal Out of Range High
- SPN 101 FMI 4Engine Crankcase Pressure Signal Out of Range Low
- SPN 102Manifold Air Pressure Signal Extremely High
- SPN 102 FMI 13Manifold Air Pressure Signal Calibrations Fault
- SPN 102 FMI 16Manifold Air Pressure Signal Moderately High
- SPN 102 FMI 2Manifold Air Pressure Signal Invalid
- SPN 103 FMI 2VGT Speed Signal Invalid
- SPN 103 FMI 31Turbo Speed Signal Missing
- SPN 103 FMI 5Turbo Speed Signal Circuit has High Resistance
- SPN 103 FMI 8Turbo Speed Signal Incorrect
- SPN 1041 FMI 3Start Signal Always Active
- SPN 105 FMI 9Manifold Air Temperature Invalid
- SPN 1069 FMI 9Tire Size Invalid
- SPN 1075 FMI 12Low-Pressure Fuel Pump Loss of Communication
- SPN 1075 FMI 15Low-Pressure Fuel Pump Temperature Slightly High
- SPN 1075 FMI 2Low-Pressure Fuel Pump Data Erratic
Other John Deere machine types
Fault code lists by brand
- CAT8,286 codes
- Volvo6,508 codes
- New Holland Tractor3,475 codes
- FPT3,033 codes
- Case IH2,992 codes
- Bobcat2,653 codes
- Challenger Tractor2,434 codes
- New Holland Combine2,274 codes
- Case Wheel Loader1,859 codes
- Cummins1,847 codes
- Challenger Rubber Track Tractor1,747 codes
- Volvo Wheel Loader1,726 codes
- Deutz1,684 codes
- Perkins1,523 codes
Safety-critical: confirm before use
Safety first: park on level ground, stop the engine, and secure the machine before any inspection. Thresholds, component locations, wire numbers, fuse locations, and reset procedures can vary by model, configuration, and serial number. Confirm them in the service documentation for your exact machine.