HeavyEquipmentFix
Ask

CAT Fault Codes List: 2504 to 2590

Page 18 of 83 of the full CAT fault code list (8,286 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

CAT codes 2504 to 2590

  • 2504Intake Valve Actuator Pressure Sensor #4
  • 2505Intake Valve Actuator Pressure Sensor #5
  • 2506Intake Valve Actuator Pressure Sensor #6
  • 2507Intake Valve Actuator Pressure Sensor #7
  • 2508Intake Valve Actuator Pressure Sensor #8
  • 2509Intake Valve Actuator Pressure Sensor #9
  • 251ECM not detecting SART module J1939
  • 2510Intake Valve Actuator Pressure Sensor #10
  • 2511Intake Valve Actuator Pressure Sensor #11
  • 2512Intake Valve Actuator Pressure Sensor #12
  • 2513Intake Valve Actuator Pressure Sensor #13
  • 2514Intake Valve Actuator Pressure Sensor #14
  • 2515Intake Valve Actuator Pressure Sensor #15
  • 2516Intake Valve Actuator Pressure Sensor #16
  • 2517Intake Valve Actuator Pressure Sensor #17
  • 2518Intake Valve Actuator Pressure Sensor #18
  • 2519Intake Valve Actuator Pressure Sensor #19
  • 252Loss of Key Table Information
  • 2520Intake Valve Actuator Pressure Sensor #20
  • 2521Generator Phase C Power Factor Lagging
  • 252-11Incorrect Engine Software
  • 252-2Calibration Module : Erratic, Intermittent, or Incorrect
  • 2523Utility Phase A Power Factor Lagging
  • 2524Utility Phase B Power Factor Lagging
  • 2525Utility Phase C Power Factor Lagging
  • 2526Bus #1/Generator Phase Match
  • 2527Bus #1/Generator Voltage Match
  • 2528Bus #1/Generator Frequency Match
  • 2529Bus #1/Generator In Sync
  • 253631 2 415 Engine software data incorrect
  • 2530Bus #1/Generator Dead Bus
  • 253-02Check Customer or System Parameters
  • 2531Bus #1/Utility Phase Match
  • 253-11Calibration Memory : Other Failure Mode
  • 253-14Truck Manufacturer Paremater Not Programmed
  • 253-2Calibration Memory : Erratic, Intermittent, or Incorrect
  • 2533Bus #1/Utility Frequency Match
  • 2534Bus #1/Utility In Sync
  • 2535Bus #1/Utility Dead Bus
  • 2536Compression Brake Medium/High Solenoid #2
  • 2537Pump to Blade Lift Rod End Solenoid
  • 2538Pump to Blade Lift Head End Solenoid
  • 2539Blade Lift Rod End to Tank Solenoid
  • 254No Detonation Derate Action Taken
  • 2540Blade Lift Head End to Tank Solenoid
  • 2541Blade Lift Rod End Pressure Sensor
  • 2542Blade Lift Head End Pressure Sensor
  • 2543Joystick Steering Enable Switch
  • 2544Offset Boom Offset Left Solenoid
  • 2545Offset Boom Offset Right Solenoid
  • 2546Hydraulic Cab Riser Raise Solenoid
  • 2547Hydraulic Cab Riser Lower Solenoid
  • 25483rd Function Maximum Flow Rate Control Position Sensor
  • 2549Left Conveyor Reverse Solenoid
  • 255Diagnostic Reset
  • 2550Right Conveyor Reverse Solenoid
  • 2551Left Hopper Raise Solenoid
  • 2552Left Hopper Lower Solenoid
  • 2553Right Hopper Raise Solenoid
  • 2554Right Hopper Lower Solenoid
  • 2555Screed Left Extender Extend Solenoid
  • 2556Screed Left Extender Retract Solenoid
  • 2557Screed Right Extender Extend Solenoid
  • 2558Screed Right Extender Retract Solenoid
  • 2559Left Station Auger Lift Switch
  • 256Steering Output Detected in Wrong Direction
  • 2560Right Station Auger Lift Switch
  • 2561Left Station Hopper Lift Switch
  • 2562Right Station Hopper Lift Switch
  • 2563Left Station Screed Height Adjustment Switch
  • 2564Right Station Screed Height Adjustment Switch
  • 2565Left Station Steering Dial Position Sensor
  • 2566Right Station Steering Dial Position Sensor
  • 2567Left Station Truck Hitch Switch
  • 2568Right Station Truck Hitch Switch
  • 2569Screed Float Solenoid
  • 257Steering Output Detected with No Command Given
  • 2570Connection abort reason detected.
  • 2571Truck Hitch Open Solenoid
  • 2572Truck Hitch Close Solenoid
  • 2573Turn Signal Switch
  • 2574Vibratory System Enable Solenoid
  • 2575Vibratory System Speed Dial
  • 2576Tilt Cylinder Regeneration Solenoid
  • 2577Counterbalance Dial
  • 2578Counterbalance Standby Switch
  • 2579Counterbalance Solenoid
  • 258No steering detected with command given
  • 2580Left Station Hopper Apron Fold Switch
  • 2581Hydraulic brake pressure circuit 2 issue.
  • 2582Hopper Apron Lower Solenoid
  • 2583Left Station Friction Steer Solenoid
  • 2584Hydraulic brake pressure warning circuit 1.
  • 2585Hydraulic brake pressure warning circuit 2.
  • 2586Tire air leakage rate detected.
  • 2587Tire pressure threshold detection.
  • 2588Vehicle overspeed 1, event log, non-extreme
  • 2589Vehicle overspeed 2, event log, non-extreme
  • 259Excessive steering system command Error
  • 2590Counterbalance Lock Solenoid
Looking for a different CAT code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Caterpillar machine types

Fault code lists by brand