HeavyEquipmentFix
Ask

Deutz Fahr Fault Codes List: 877 to 9976

Page 10 of 11 of the full Deutz Fahr fault code list (1,004 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Deutz Fahr codes 877 to 9976

  • 877Sensor Error Rail Pressure; Signal Range Check High
  • 878Sensor Error Rail Pressure; Signal Range Check Low
  • 88Charged Air Pressure Above Warning Threshold
  • 881NOx Conversion Rate Insufficient (SCR-Cat Defect, Bad Diesel Exhaust Fluid Quality)
  • 882NOx Conversion Rate Insufficient (SCR-Cat Defect, Bad Diesel Exhaust Fluid Quality); Temperature Range 1
  • 883NOx Conversion Rate Insufficient (SCR-Cat Defect, Bad Diesel Exhaust Fluid Quality); Temperature Range 2
  • 887NOx Sensor Downstream of SCR Catalysator; Plausibility Error "Stuck in Range"
  • 889NOx Sensor Upstream of SCR Catalysator; Low Signal Not Plausible
  • 89Charged Air Pressure Above Shut Off Threshold
  • 892Sensor Back Flow Line Pressure (SCR); Plausibility Error
  • 893General Pressure Check Error (SCR)
  • 894Pressure Stabilization Error Dosing Valve (SCR)
  • 896Detection of Diesel Exhaust Fluid Filled SCR System in Init-State
  • 897Pump Pressure SCR Metering Unit Too High
  • 898Pump Pressure SCR Metering Unit Too Low
  • 899Pressure Overload of SCR-System
  • 9Sensor Ambient Air Temperature; Plausibility Error
  • 900Pressure Build-Up Error SCR-System
  • 903Urea Tank Temperature Too High
  • 905Sensor SCR Catalyst Upstream Temperature Too High; Plausibility Error
  • 906Sensor SCR Catalyst Upstream Temperature Too Low; Plausibility Error
  • 908Diesel Exhaust Fluid Dosing Valve Blocked (SCR)
  • 914Sensor Urea Supply Module Heater Temperature; Plausibility Error (Normal Condition)
  • 915Sensor Urea Supply Module Heater Temperature; Plausibility Error (Cold Start Condition)
  • 916Sensor Urea Supply Module Temperature; Plausibility Error (Normal Condition)
  • 917Sensor Urea Supply Module Temperature; Plausibility Error (Cold Start Condition)
  • 918Urea-Tank without Heating Function (Heating Phase)
  • 919Immobilizer Status; Fuel Blocked
  • 925Urea Supply Module Heater Temperature; Duty Cycle in Failure Range
  • 926Urea Supply Module Heater Temperature; Duty Cycle in Invalid Range
  • 927Urea Supply Module Temperature Measurement Not Available
  • 928Urea Supply Module PWM Signal; Period Outside Valid Range
  • 929Detect Faulty PWM Signal From Supply Module
  • 930Urea Supply Module Temperature; Duty Cycle in Failure Range
  • 931Urea Supply Module Temperature; Duty Cycle in Invalid Range
  • 932Hand Throttle Idle Validation Switch; Short Circuit to Battery
  • 935Sensor Error Accelerator Pedal; Signal Range Check High
  • 936Sensor Error Hand Throttle; Signal Range Check High
  • 937Hand Throttle Idle Validation Switch; Short Circuit to Ground
  • 940Sensor Error Accelerator Pedal; signal range Check Low
  • 941Sensor Error Hand Throttle Sensor; Signal Range Check Low
  • 942Sensor Error Burner Temperature; Signal Range Check High
  • 943Sensor Error Urea Tank Level; Signal Range Check High
  • 944Sensor Error Burner Temperature; Signal Range Check Low
  • 945Sensor Error Urea Tank Level; Signal Range Check Low
  • 946Sensor Supply Voltage Monitor 1 Error (ECU)
  • 947Sensor Supply Voltage Monitor 2 Error (ECU)
  • 948Sensor Supply Voltage Monitor 3 Error (ECU)
  • 956Starter Relay High Side; Short Circuit to Battery
  • 957Starter Relay High Side; Short Circuit to Ground
  • 958Starter Relay; No Load Error
  • 959Starter Relay; Power Stage Over Temperature
  • 96Sensor Error Coolant Temperature; Signal Range Check High
  • 960Starter Relay Low Side; Short Circuit to Battery
  • 961Starter Relay Low Side; Short Circuit to Ground
  • 963Burner Shut Off Valve; Open Load
  • 965Burner Shut Off Valve; Short Circuit to Battery
  • 967Burner Shut Off Valve; Short Circuit to Ground
  • 969SVS Lamp; Open Load
  • 97Sensor Error Coolant Temperature; Signal Range Check Low
  • 970SVS Lamp; Power Stage Over Temperature
  • 971SVS Lamp; Short Circuit to Battery
  • 972SVS Lamp; Short Circuit to Ground
  • 973Software Reset CPU SWReset 0
  • 974Software Reset CPU SWReset 1
  • 975Software Reset CPU SWReset 2
  • 976Plausibility Error Between APPl and APP2 or APPl and Idle Switch
  • 98High Coolant Temperature; Warning Threshold Exceeded
  • 980T50 Start Switch Active for Too Long
  • 981Sensor Error Intake Air; Signal Range Check High
  • 982Sensor Error Intake Air Sensor; Signal Range Check Low
  • 983Intake Air Sensor; Plausibility Error
  • 984Sensor Burner Temperature; Plausibility Error
  • 986Physical Range Check High for Burner Temperature
  • 989Physical Range Check Low for Burner Temperature
  • 99High Coolant Temperature; Shut Off Threshold Exceeded
  • 991Hardware - LSS Watchdog Reset
  • 9910Hardware - Function Locked Out - Platform Module Software Version Improper
  • 9911Hardware - Function Locked Out - LSS Module Software Version Improper
  • 9915Hardware - Chassis Tilt Sensor Not Gain Calibrated
  • 99151Hardware - Functions Locked Out - LSI Software Version Improper
  • 99152Hardware - LSI Faulty - System Flash CRC Error
  • 99153Hardware - LSI Faulty - Data Flash CRC Error
  • 99154Hardware - LSI Faulty - Load Cells A and B Disagreement
  • 99161Functions Locked Out - Remote Input Module Software Version Improper
  • 992Hardware - LSS EEPROM Error
  • 9921Hardware - Ground Module Failure - High Side Driver Cutout Faulty
  • 9924Hardware - Functions Locked Out - Machine Not Configured
  • 993Hardware - LSS Internal Error - Pin Excitation
  • 994Sensor Error Charged Air Temperature; Signal Range Check High
  • 9944Hardware - Current Feedback Gains Out of Range
  • 9945Hardware - Current Feedback Calibration Checksum Incorrect
  • 9946Hardware - Cabin Display EEPROM Write Failure
  • 9947Hardware - Hardware Exchange Required
  • 9948Hardware - Platform Module Hardware Failure
  • 9949Hardware - Machine Configuration Out of Range - Check All Settings
  • 995Sensor Error Charged Air Temperature; Signal Range Check Low
  • 996High Charged Air Cooler Temperature; Warning Threshold Exceeded
  • 997High Charged Air Cooler Temperature; Shut Off Threshold Exceeded
  • 9976Hardware - Cabin Joystick - Internal Failure
Looking for a different Deutz Fahr code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Deutz machine types

Fault code lists by brand