HeavyEquipmentFix
Ask

John Deere Tractors Fault Codes List: SPN 752 FMI 3 to SPN 99

Page 19 of 19 of the full John Deere Tractors fault code list (1,884 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

John Deere Tractors codes SPN 752 FMI 3 to SPN 99

  • SPN 752 FMI 3Potentiometer for PowerShuttle Transmission, Input Voltage Too High
  • SPN 752 FMI 4Potentiometer for PowerShuttle Transmission, Input Voltage Too Low
  • SPN 76Lock Position Switch of the Multi-Function Lever, Status
  • SPN 765 FMI 12DOC Inlet Temperature Fault
  • SPN 77Correction for Battery Temperature Calculation, Configuration
  • SPN 78Remote Control of Rear PTO, Configuration
  • SPN 79Right Brake Pedal, Maximum Voltage
  • SPN 8Transmission Oil Temperature Sensor, Voltage
  • SPN 80Overvoltage Protection of Configured Worklights, Configuration
  • SPN 81Right Dome Light with Switch/Console Light, Configuration
  • SPN 82Alternator Charging Log, Configuration
  • SPN 823821 FMI 2Incompatible Harness on Steering Control Unit (AutoTrac)
  • SPN 841 FMI 5GPS Antenna Error - Open Circuit
  • SPN 841 FMI 6GPS Antenna Error - Grounded/Short Circuit
  • SPN 84 FMI 14INFORMATION FOR OPERATOR: Travel Speed Too High
  • SPN 84 FMI 15Wheel Speed Detected During Calibration
  • SPN 84 FMI 19Incorrect CAN Bus Message, Wheel Speed Signal Incorrect
  • SPN 84 FMI 31Wheel Speed Sensor, Malfunction
  • SPN 84 FMI 4Wheel Speed Sensor, Voltage Too Low
  • SPN 84 FMI 5Wheel Speed Sensor, Current Too Low
  • SPN 84 FMI 7Wheel Speed Detected During Calibration of Transmission
  • SPN 85Tire Index (SRI) of Mounted Rear Wheel, Status
  • SPN 86Forced Shut-Off of Worklights, Configuration
  • SPN 87Rear Hitch Slip, Display in %
  • SPN 871 FMI 13Sensor for Refrigerant Pressure, Refrigerant Pressure Out of Valid Range Low
  • SPN 871 FMI 18Refrigerant Pressure Sensor, Malfunction
  • SPN 871 FMI 3Refrigerant Pressure Sensor, Voltage Too High
  • SPN 871 FMI 4Refrigerant Pressure Sensor, Voltage Too Low
  • SPN 876 FMI 10Compressor Clutch, Malfunction
  • SPN 876 FMI 14Compressor Clutch, Overload Protection
  • SPN 876 FMI 3Compressor Clutch Switched On, Voltage Too High
  • SPN 876 FMI 4Compressor Clutch Switched On, Voltage Too Low
  • SPN 88Self-Cancellation of Turn-Signal Lights, Configuration
  • SPN 89Tire Index (SRI) of Mounted Front Wheel, Status
  • SPN 898 FMI 19Incorrect CAN Bus Message, Engine Speed Not Detected or Incorrect
  • SPN 9Remote Control Switch for Hitch (Raise), Status
  • SPN 90Clearance Lights, Configuration
  • SPN 90 FMI 3Rear PTO Oil Temperature Sensor Circuit Voltage High
  • SPN 90 FMI 4Rear PTO Oil Temperature Sensor Circuit Voltage Low
  • SPN 91Hitch Dampening, Configuration
  • SPN 910 FMI 19Incorrect CAN BUS Message, Engine Speed Not Detected
  • SPN 91 FMI 2Accelerator Pedal Potentiometer, Voltages at Channel 1 and Channel 2 Not in the Correct Ratio
  • SPN 91 FMI 3Accelerator Pedal Potentiometer, Voltage at Channel 1 Too High
  • SPN 91 FMI 4Accelerator Pedal Potentiometer, Voltage at Channel 1 Too Low
  • SPN 9212-Volt Supply Voltage 1, Display in Milliamps and Status
  • SPN 920 FMI 3Acoustic Alarm, Voltage Too High
  • SPN 920 FMI 6Acoustic Alarm, Current Too High
  • SPN 923 FMI 12Circulation Blower Motor Internal Fault
  • SPN 923 FMI 3Circulation Blower Motor On, Voltage Too High
  • SPN 923 FMI 4Circulation Blower Motor On, Voltage Too Low
  • SPN 924 FMI 3Stepper Motors for E-SCV X and E-SCV XI, Supply Voltage Too High
  • SPN 924 FMI 4Stepper Motors for E-SCV X and E-SCV XI, Supply Voltage Too Low
  • SPN 925 FMI 3Stepper Motor for E-SCV XII, Supply Voltage Too High
  • SPN 925 FMI 4Stepper Motor for E-SCV XII, Supply Voltage Too Low
  • SPN 926 FMI3Stepper Motor for E-SCV XIII, Supply Voltage Too High
  • SPN 926 FMI 4Stepper Motor for E-SCV XIII, Supply Voltage Too Low
  • SPN 9312-Volt Supply Voltage 2, Display in Milliamps and Status
  • SPN 94Distance (in Meter) for the Quick Lowering with iTEC™, Configuration
  • SPN 94 FMI 16Low-Pressure Fuel Signal Moderately High
  • SPN 94 FMI 17Low-Pressure Fuel Signal Slightly Low
  • SPN 94 FMI 18Low-Pressure Fuel Signal Moderately Low
  • SPN 94 FMI 3Low-Pressure Fuel Signal Out of Range High
  • SPN 94 FMI 4Low-Pressure Fuel Signal Out of Range Low
  • SPN 955-Volt Supply Voltage 2, Display in Milliamps and Status
  • SPN 964 FMI 13Real Time Clock Failure
  • SPN 96 FMI 17Fuel Level Too Low
  • SPN 96 FMI 3Fuel Level Sensor Circuit Voltage High
  • SPN 96 FMI 4Fuel Level Sensor Circuit Voltage Low
  • SPN 96 FMI 9Incorrect CAN Bus Message, Information from CCU Control Software
  • SPN 97Low Fuel Level Acoustic Alarm, Configuration
  • SPN 970 FMI 31Immobilizer Fault
  • SPN 974 FMI 2Hand Throttle Potentiometer, Voltages at Channel 1 and Channel 2 Not in the Correct Ratio
  • SPN 974 FMI 3Hand Throttle Potentiometer, Voltage at Channel 1 Too High
  • SPN 974 FMI 4Hand Throttle Potentiometer, Voltage at Channel 1 Too Low
  • SPN 97 FMI 16Water-In-Fuel Level Moderately High
  • SPN 97 FMI 3Water-In-Fuel Signal Voltage Out of Range High
  • SPN 97 FMI 4Water-In-Fuel Signal Voltage Out of Range Low
  • SPN 99Stored Maximum Temperature of Control Unit
Looking for a different John Deere Tractors code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other John Deere machine types

Fault code lists by brand