John Deere Tractors Fault Codes List: SPN 516317 FMI 6 to SPN 521161 FMI 8
Page 9 of 19 of the full John Deere Tractors fault code list (1,884 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.
John Deere Tractors codes SPN 516317 FMI 6 to SPN 521161 FMI 8
- SPN 516317 FMI 612-Volt Supply Voltage 2, Current Too High
- SPN 516446 FMI 9LIN Bus Message Cannot Be Received, Information from LIN Bus Module (Positions F and G)
- SPN 516454 FMI 12E-SCV X Not Calibrated
- SPN 516454 FMI 13E-SCV X Not Calibrated
- SPN 516454 FMI 14CAN Bus Message Cannot Be Received, Information from E-SCV X
- SPN 516454 FMI 3E-SCV X Not Calibrated
- SPN 516454 FMI 4E-SCV X Not Calibrated
- SPN 516455Stepper Motor for E-SCV X, Temperature Too High
- SPN 516455 FMI 1Stepper Motor for E-SCV X, Temperature Too Low
- SPN 516455 FMI 18Stepper Motor for E-SCV X, Hydraulic Oil Temperature and Supply Voltage Too Low
- SPN 516457 FMI 14Control Software Internal Fault
- SPN 516458Stepper Motor for E-SCV X, Supply Voltage Too High
- SPN 516458 FMI 1Stepper Motor for E-SCV X, Supply Voltage Too Low
- SPN 516460 FMI 3E-SCV X, Voltage Too High
- SPN 516460 FMI 4E-SCV X, Voltage Too Low
- SPN 516461 FMI 2Multi-Function Lever Out of Range
- SPN 51 FMI 14Air Throttle Actuator and EGR Valve Connectors Swapped
- SPN 51 FMI 3Air Throttle Actuator Position Signal Out of Range High
- SPN 51 FMI 4Air Throttle Actuator Position Signal Out of Range Low
- SPN 51 FMI 7Air Throttle Actuator Fault
- SPN 52Park Position of Windshield and Rear Window Wipers and Module Wake-Up Signal, Status
- SPN 5200772 FMI 12Control Software, Internal Fault
- SPN 520194 FMI 2VIN Information, Mismatch
- SPN 520211 FMI 5USB Memory Device Removed During Software Installation
- SPN 520257 FMI 2Auto-Mode Switch Fault
- SPN 520273 FMI 3Console Light, Voltage Too High
- SPN 520273 FMI 5Console Light, Current Too Low
- SPN 520273 FMI 6Console Light, Current Too High
- SPN 520285 FMI 2Transport Lock/Hitch Dampening Button Fault
- SPN 520285 FMI 3Transport Lock/Hitch Dampening Button, Voltage Too High
- SPN 520285 FMI 9Incorrect LIN Bus Message from Hitch Lock Switch
- SPN 520286 FMI 11Quick Raise/Lower Switch Fault
- SPN 520286 FMI 2Quick Raise/Lower Switch for Lower End Point, Error
- SPN 520286 FMI 4Quick Raise/Lower Switch, Voltage Too Low
- SPN 520286 FMI 9Incorrect LIN Bus Message from Quick Raise/Lower Switch for Lower End Point
- SPN 520425 FMI 7Received CAN Bus Messages, High Error Rate
- SPN 520426 FMI 7Transmitted CAN Bus Messages, High Error Rate
- SPN 520451 FMI 31INFORMATION FOR OPERATOR: Operator Presence Switch Not Activated While E-SCV XIV is Activated
- SPN 520490 FMI 3Implement Supply Voltage, Voltage Too High
- SPN 520490 FMI 6Implement Supply Voltage, Current Too High
- SPN 520491 FMI 3Supply Voltage for a Control Unit on Implement, Voltage Too High
- SPN 520491 FMI 6Supply Voltage for a Control Unit on Implement, Current Too High
- SPN 520529 FMI 12Loader Boom Position Sensor Fault
- SPN 520529 FMI 16Loader Boom Position Sensor Value Too High
- SPN 520529 FMI 18Loader Boom Position Sensor Value Too Low
- SPN 520529 FMI 3Loader Boom Position Sensor (Channel 1), Voltage Too High
- SPN 520529 FMI 31Loader Boom Position Sensor, Voltage Ratio Between Channel 1 and Channel 2 Not Correct
- SPN 520529 FMI 4Loader Boom Position Sensor (Channel 1) Voltage Too Low
- SPN 520529 FMI 7Loader Boom Position Sensor Fault
- SPN 520530 FMI 3Loader Boom Position Sensor (Channel 2), Voltage Too High
- SPN 520530 FMI 4Loader Boom Position Sensor (Channel 2), Voltage Too Low
- SPN 520531 FMI 11Loader Bucket Position Sensor Fault
- SPN 520531 FMI 12Loader Bucket Position Sensor Fault
- SPN 520531 FMI 14Return-to-Position Function Fault
- SPN 520531 FMI 18Loader Bucket Position Sensor Value Too High
- SPN 520531 FMI 3Loader Bucket Position Sensor, Voltage Too High
- SPN 520531 FMI 4Loader Bucket Position Sensor, Voltage Too Low
- SPN 520531 FMI 7Loader Bucket Position Sensor Fault
- SPN 520542 FMI 3Vehicle CAN Bus (500 kBd), Voltage Too High
- SPN 520543 FMI 4Vehicle CAN Bus (500 kBd), Voltage Too Low
- SPN 520629 FMI 31Control Software Internal Fault
- SPN 520715 FMI 3Pressurizer Fan Motor for Pressure Inside Cab, Voltage Too High
- SPN 520715 FMI 5Fan Motor for Pressure Inside Cab, Current Too Low
- SPN 520715 FMI 6Fan Motor for Pressure Inside Cab, Current Too High
- SPN 52080 FMI 13Suspended Front-Wheel Drive Axle, Fault During Calibration
- SPN 520870 FMI 13Control Software Not or Incorrectly Calibrated
- SPN 520870 FMI 2Control Software Internal Fault
- SPN 520871 FMI 13Control Software Internal Fault
- SPN 520871 FMI 2Control Software Internal Fault
- SPN 520872 FMI 2Control Software Internal Fault
- SPN 520873 FMI 2Control Software Internal Fault
- SPN 520874 FMI 2Control Software Internal Fault
- SPN 520892 FMI 2Control Software Internal Fault
- SPN 520893 FMI 2Control Software Internal Fault
- SPN 520958 FMI 14INFORMATION FOR OPERATOR: Shifting Transmission Not Permitted
- SPN 520958 FMI 31INFORMATION FOR OPERATOR: Shifting Transmission Not Permitted, Maximum Travel Speed Will Be Exceeded
- SPN 520959 FMI 14INFORMATION FOR OPERATOR: No Valid Signal From Operator Presence Switch During Shifting
- SPN 520965 FMI 3CAN BUS Terminating Resistor, CAN BUS Voltage Too High
- SPN 520965 FMI 4CAN BUS Terminating Resistor, CAN BUS Voltage Too Low
- SPN 520965 FMI 6CAN BUS Terminating Resistor, CAN BUS Current Too High
- SPN 5210000 FMI 2Switch for Remote Control of Hitch (Left or Right), Circuit Fault
- SPN 5210000 FMI 31Switch for Remote Control of Hitch (Left or Right), Fault
- SPN 521000 FMI 2Left Remote Control Switch for E-SCVs, Fault
- SPN 521000 FMI 31Switch for Remote Control of Hitch (Right/Left), Malfunction
- SPN 521001 FMI 11Solenoid Valve for Raising (Hitch), Fault During Calibration
- SPN 521001 FMI 13Solenoid Valve for Raising (Hitch), Fault During Calibration
- SPN 521001 FMI 2Solenoid Valve for Raising (Hitch), Current Too High During Calibration
- SPN 521001 FMI 5Solenoid Valve for Raising (Hitch), Current Too Low
- SPN 521001 FMI 6Solenoid Valve for Raising (Hitch), Current Too High
- SPN 521001 FMI 7Solenoid Valve for Raising (Hitch), Fault During Calibration
- SPN 521002 FMI 11Solenoid Valve for Lowering (Hitch), Fault During Calibration
- SPN 521002 FMI 13Solenoid Valve for Lowering (Hitch), Fault During Calibration
- SPN 521002 FMI 5Solenoid Valve for Lowering (Hitch), Current Too Low
- SPN 521002 FMI 6Solenoid Valve for Lowering (Hitch), Current Too High
- SPN 521002 FMI 7Solenoid Valve for Lowering (Hitch), Fault During Calibration
- SPN 521156 FMI 12Control Software, Internal Fault
- SPN 521160 FMI 2Button for Volume Control (Lower Volume), Fault
- SPN 521160 FMI 8Button for Volume Control (Lower Volume), Fault
- SPN 521161 FMI 2Button for Volume Control (Raise Volume), Fault
- SPN 521161 FMI 8Button for Volume Control (Raise Volume), Fault
Other John Deere machine types
Fault code lists by brand
- CAT8,286 codes
- Volvo6,508 codes
- New Holland Tractor3,475 codes
- FPT3,033 codes
- Case IH2,992 codes
- Bobcat2,653 codes
- Challenger Tractor2,434 codes
- New Holland Combine2,274 codes
- Case Wheel Loader1,859 codes
- Cummins1,847 codes
- Challenger Rubber Track Tractor1,747 codes
- Volvo Wheel Loader1,726 codes
- Deutz1,684 codes
- Perkins1,523 codes
Safety-critical: confirm before use
Safety first: park on level ground, stop the engine, and secure the machine before any inspection. Thresholds, component locations, wire numbers, fuse locations, and reset procedures can vary by model, configuration, and serial number. Confirm them in the service documentation for your exact machine.