HeavyEquipmentFix
Ask

New Holland Combine Fault Codes List: A0133 to E0047

Page 9 of 23 of the full New Holland Combine fault code list (2,274 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

New Holland Combine codes A0133 to E0047

  • A0133Rotor Motor Exceeded 5000 RPM
  • A0134Feeder Sensor Out of Range - Feeder Position Displayed Will be Inaccurate
  • A0137Display "Disengage Chopper Counter Knives" on Trigger Conditions
  • A0138Ground Drive
  • A0140DEF Tank Temperature High
  • A0143Feeder Reverser
  • A0145Load Spout Not in Commanded Position
  • A0146Move Unload Spout Down
  • A0147Unload Tube - Cannot Fold/Unfold if Vehicle Moving
  • A0148Unload Tube - Cannot Fold/Unfold if Tube is Not in Cradle
  • A0149Unload Tube - Cannot Fold if Unloader is Engaged
  • A0150Unload Tube - Cannot Swing Out if Not Completely Unfolded
  • A0153Augerbed RPM Low
  • A0154Hydromotor Overspeed Detected
  • A0157Reposition Chopper Counter Knife, Concave
  • A0158Chopper Counter Knives Not in Commanded Position
  • A0159Operator Not Seated - Procedure to Stop Combine Will Start in 5 Seconds
  • A0160Operator Not Seated - Vehicle Speed Shall be Reduced Automatically to 0
  • A0161Operator Not Seated - Park Brake Engaged Automatically
  • A0163Spreader Left Not in Commanded Position
  • A0164Spreader Right Not in Commanded Position
  • A0165Spreader Distribution Not in Commanded Position
  • A0166Ground Drive Failure
  • A0167Deslug Operation Not Allowed
  • A0168Ground Drive
  • A0169Power Guide Axle
  • A0170Feeder Reverser
  • A0171Chop to Swath System
  • A0172Chop to Swath System
  • A0173Chop to Swath System
  • A0178Chop to Swath System
  • A0179Chop to Swath System
  • A0180Chop to Swath System
  • A0181Chop to Swath System
  • A0192Tracks Low Pressure
  • A0193Chop to Swath System
  • A0194Chop to Swath System
  • A0195Chop to Swath System
  • A0197"Residue Distribution System Calibration"
  • A1Controller Area Network (CAN) Receive Frame E2SCR (Diesel Exhaust Fluid DEF Quantity Not in Range)
  • A2029HVAC Not Detected
  • A2030HVAC Communication Lost
  • A2044UCM3 Not Detected
  • A3Controller Area Network (CAN) Receive Frame EEC1 Engine Torque Not in Range
  • A36EDownstream NOx Sensor Internal Failure (Heater Performance Plausibility Error)
  • A4Controller Area Network (CAN) Receive Frame ET1 (Oil and Water Temperature Engine) - Bad Intelligent Device
  • A66EUpstream NOx Sensor Internal Failure (Heater Performance Plausibility Error)
  • AAUrea Tank Level Error (CAN Message or Electrical with Real Sensor), Shorted to High Source
  • B1Ambient Temperature - Controller Area Network (CAN) Signal Ambient Air Temperature Not in Range
  • BD1EEPROM/Checksum Failures - Bad Intelligent Device
  • D1EEPROM/Checksum Failures - Mechanical Out of Range
  • D2Ignition "On" Signal K15
  • D3Main Relay Shut Off Too Early Before EEPROM Update
  • D4Too High Diesel Exhaust Fluid DEF Temperature in Pump Module
  • E0000Stone Trap Closed Sensor Shorted to High Source
  • E0001Grain Tank Covers Closed Sensor - Shorted to High Source
  • E0002Swath Plate Position Shorted to High Source
  • E0003Unload Tube Cradled Shorted to High Source
  • E0004FDR Reverser Disengaged Shorted to High Source
  • E0005Straw Walker Protection Shorted to High Source
  • E0006Return Filter Bypass Shorted to High Source
  • E0007Gearbox Filter Bypass Shorted to High Source
  • E0008Left Turn Signal Shorted to Low Source
  • E0009Front Work Lights Switch Shorted to Low Source
  • E0010Rear Work Lights Switch Shorted to Low Source
  • E0011Road Lights Signal Shorted to Low Source
  • E0012Right Turn Signal Shorted to Low Source
  • E0013Cleaning Fan RPM Sensor Shorted to High Source
  • E0014Hydraulic Reservoir Temperature Sensor - Shorted to High Source
  • E0015Left Returns RPM Sensor Shorted to High Source
  • E0016Clean Grain Elevator RPM Shorted to High Source
  • E0017Rotary Separator RPM Shorted to High Source
  • E0018Right Returns RPM Sensor Shorted to High Source
  • E0019Right Header Height/Tilt Sensor - Shorted to High Source
  • E0020Early Grain Evacuation RPM Sensor - Shorted to High Source
  • E0021Clean Grain Elevator Speed Sensor - Shorted to High Source
  • E0023Right Returns RPM Sensor - Shorted to High Source
  • E0024Hydraulic Reservoir Temp Shorted to High Source
  • E0025Gearbox Temp Sensor Shorted to High Source
  • E0026Rear Ladder Sensor Shorted to High Source
  • E0027Left Center Header Height Sensor - Shorted to High Source
  • E0028Right Center Header Height Sensor - Shorted to High Source
  • E0029Lateral Float Sensor Shorted to High Source
  • E0030Header Lift Pressure Sensor - Shorted to High Source
  • E0031Hydrostat Motor Temperature Sensor - Shorted to High Source
  • E0032Shoe Position Sensor Shorted to High Source
  • E0033Lateral Inclination Sensor - Shorted to High Source
  • E0034Concave Position Sensor Shorted to High Source
  • E0036Grain Tank Covers Open Sensor - Shorted to High Source
  • E0037CCM1 5V Ref Voltage 3 Shorted to High Source
  • E0038CCM1 8V Ref Voltage Shorted to High Source
  • E0039CCM1 5V Ref Voltage 1 Shorted to High Source
  • E0040Spreader Left Position - Shorted to High Source
  • E0041Current Sense Fan Motor Short Circuit
  • E0042Current Sense Reverser Short Circuit
  • E0043Spreader Distribution Position - Shorted to High Source
  • E0044Current Sense Concave CL Short Circuit
  • E0045Reel Horizontal Position - Shorted to High Source
  • E0046Header Height Sens RC - Shorted to High Source
  • E0047V Supply Feeder Clutch Shorted to High Source
Looking for a different New Holland Combine code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other New Holland machine types

Fault code lists by brand