Bobcat Fault Codes List: W1407 to W4350
Page 23 of 24 of the full Bobcat fault code list (2,653 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.
Bobcat codes W1407 to W4350
- W1407PVG32 Frame Leveling Valve Open circuit
- W1428PVG32 Frame Leveling Valve in error
- W1505Pedal lock shorted to battery
- W1506Pedal lock shorted to ground
- W1507Pedal lock open circuit
- W1605Handle lock shorted to battery
- W1606Handle lock shorted to ground
- W1607Handle lock open circuit
- W1824Frame leveling potentiometer out of neutral
- W2021Lift handle sensor out of range high
- W2022Lift handle sensor out of range low
- W2121Lift pedal sensor out of range high
- W2122Lift pedal sensor out of range low
- W2205Lift up output shorted to battery
- W2206Lift up output shorted to ground
- W2207Lift up output open circuit
- W2221Tilt handle sensor out of range high
- W2222Tilt handle sensor out of range low
- W2232Lift up output overcurrent
- W2305Lift down output shorted to battery
- W2306Lift down output shorted to ground
- W2307Lift down output open circuit
- W2321Tilt pedal sensor out of range high
- W2322Tilt pedal sensor out of range low
- W2332Lift down output overcurrent
- W2405Tilt out output shorted to battery
- W2406Tilt out output shorted to ground
- W2407Tilt out output open circuit
- W2432Tilt out output overcurrent
- W2505Tilt back output shorted to battery
- W2506Tilt back output shorted to ground
- W2507Tilt back output open circuit
- W2532Tilt back output overcurrent
- W2605Extend output shorted to battery
- W2606Extend output shorted to ground
- W2607Extend output open circuit
- W2632Extend output overcurrent
- W2705Retract output shorted to battery
- W2706Retract output short to ground
- W2707Retract output open circuit
- W2732Retract output overcurrent
- W2824Lift input not in neutral
- W2924Tilt input not in neutral
- W3128Interrupted power failure
- W3204ACS (AHC) No Communication to OEM Controller
- W3224ACS Controller Calibration Successful
- W3225ACS (AHC) Actuator Calibration Failed
- W3228Controller failure
- W3232ACS (AHC) Tilt Actuator Wiring
- W3233ACS (AHC) Tilt Handle Wiring
- W3237ACS (AHC) Lift Actuator Wiring
- W3238ACS (AHC) Lift Handle Wiring
- W3241ACS (AHC) No Communication
- W3257ACS (AHC) Lift Actuator Reduced Performance
- W3258ACS (AHC) Tilt Actuator Reduced Performance
- W3268ACS (AHC) Lift Handle Information Error
- W3269ACS (AHC) Control Mode Toggle Switched While Operating
- W3270ACS (AHC) Right Drive Handle Short to Ground
- W3271ACS (AHC) Right Drive Handle Short to Battery
- W3274ACS (AHC) Left Joystick X-Axis Out of Range
- W3296Workgroup Calibration Failed
- W3297ACS (AHC) Controller Programmed
- W3304Gateway controller No communication
- W3404Display controller No communication
- W3604Engine controller No communication
- W3704Drive controller No communication
- W3804LLMC No communication
- W3818LLMC Out of Range
- W3844LLMC Not matching
- W3845LLMC Not matching level 2
- W3904Left Joystick No Communication
- W3918LLMI Out of Range
- W4004Right Joystick No Communication
- W4010Joystick Left roller Out Of Neutral (Extend Retract)
- W4028Joystick Grip Fault
- W4205Remote Left Joystick X Axis OON
- W4206Remote Right Joystick X Axis OON
- W4207Remote Left Joystick Y Axis OON
- W4208Right joystick Y axis out of normal range
- W4215Left joystick X axis error
- W4216Right joystick X axis error
- W4217Left joystick Y axis error
- W4218Right joystick Y axis error
- W4320Remote control not connected to manbasket harness (CAN Bus)
- W4321Remote control not connected to manbasket harness (GACD status)
- W4325Manbasket detection error
- W4326Manbasket not detected on carriage
- W4327Manbasket not detected with GACD or remote control active
- W4330Manbasket retract switch error
- W4331No boom extension when expected
- W4335Stabilizers error
- W4336Stabilizers not on the ground
- W4340Boom angle error
- W4341Unexpected boom lift movement
- W4342No boom lift movement when expected
- W4343Boom angle limit exceeded
- W4345LLM error
- W4346LLM in reduced zone
- W4347Max allowed value for longitudinal stability reached
- W4350Frame leveling error
Fault code lists by brand
- CAT8,286 codes
- Volvo6,508 codes
- New Holland Tractor3,475 codes
- FPT3,033 codes
- Case IH2,992 codes
- Challenger Tractor2,434 codes
- New Holland Combine2,274 codes
- John Deere Tractors1,884 codes
- Case Wheel Loader1,859 codes
- John Deere Engines1,853 codes
- Cummins1,847 codes
- Challenger Rubber Track Tractor1,747 codes
- Volvo Wheel Loader1,726 codes
- Deutz1,684 codes
Safety-critical: confirm before use
Safety first: park on level ground, stop the engine, and secure the machine before any inspection. Thresholds, component locations, wire numbers, fuse locations, and reset procedures can vary by model, configuration, and serial number. Confirm them in the service documentation for your exact machine.