HeavyEquipmentFix
Ask

Bobcat Fault Codes List: W4351 to W9999

Page 24 of 24 of the full Bobcat fault code list (2,653 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Bobcat codes W4351 to W9999

  • W4351Frame leveling angle exceeded
  • W4355Interlocking pin error
  • W4356Interlocking pin unlocked
  • W4360Manbasket overload error
  • W4361Manbasket overload detected
  • W4362Manbasket overload error Level 2
  • W4365Tilt angle error
  • W4366Tilt angle limit exceeded
  • W4370FNR error
  • W4371Park brake error
  • W4372Swash plate position error
  • W4404GACD controller no communication on CAN Bus
  • W4621Vsensor 5V supply high out of range
  • W4622Vsensor 5V supply low out of range
  • W4721Sensor supply high out of range
  • W4722Sensor supply low out of range
  • W4902Blue lights output short to battery or open circuit
  • W4903Blue lights output short to ground
  • W5004Lift float failure to maintain position
  • W5005Rear diverter 1 output short to battery
  • W5006Rear diverter 1 output short to ground
  • W5007Rear diverter 1 output open circuit
  • W5102Rear diverter 2 output error on
  • W5103Rear diverter 2 output error off
  • W5107Rear diverter 2 output open circuit
  • W5202Rear diverter 2 relay feedback error on
  • W5203Rear diverter 2 relay feedback error off
  • W5302Front/rear diverter sensor error on
  • W5303Front/rear diverter sensor error off
  • W5402Boom worklights output short to battery or open circuit
  • W5403Boom worklights output short to ground
  • W5502Mirror worklights output short to battery or open circuit
  • W5503Mirror worklights output short to ground
  • W5602Mirror defrost output short to battery or open circuit
  • W5603Mirror defrost output short to ground
  • W6021Inclinometer sensor input out of range high
  • W6022Inclinometer sensor input out of range low
  • W6099Inclinometer calibration required
  • W6102Inclinometer lamp error on
  • W6103Inclinometer lamp error off
  • W6521Boom angle 1 out of range high
  • W6522Boom angle 1 out of range low
  • W6621Boom angle 2 out of range high
  • W6622Boom angle 2 out of range low
  • W6744Boom angle error detected
  • W6799Boom angle calibration required
  • W6802Boom retract switch short to battery
  • W6803Boom retract switch short to ground or open circuit
  • W6902Boom retract switch 2 short to battery
  • W6903Boom retract switch 2 short to ground or open circuit
  • W6928Boom retract switch 2 in error
  • W7002Boom drain output error on
  • W7003Boom drain output error off
  • W7007Boom drain output open circuit
  • W7033Boom drain output internal failure
  • W7102Boom drain relay feedback output error on
  • W7103Boom drain relay feedback output error
  • W7304Remote control communication failure
  • W7428Boom suspension error
  • W7504Drive controller communication failure
  • W7528Boom suspension/float switch active
  • W7602Boom suspension icon error active
  • W7603Boom suspension icon error inactive
  • W7705Boom float output short to battery
  • W7706Boom float output short to ground
  • W7707Boom float output open circuit
  • W8002Power quicktach output error active
  • W8003Power quicktach output error inactive
  • W8005Power quicktach output short to battery
  • W8006Power quicktach output short to ground
  • W8007Power quicktach output open circuit
  • W8128Power quicktach switch error
  • W8202Power quicktach relay feedback error active
  • W8203Power quicktach relay feedback error inactive
  • W8302Electromagnet output error active
  • W8303Electromagnet output error inactive
  • W8307Electromagnet output open circuit
  • W8402Electromagnet relay feedback error active
  • W8403Electromagnet relay feedback error inactive
  • W8502Manplatform detection switch short to battery
  • W8503Manplatform detection switch short to ground or open
  • W8611Winch overloaded
  • W8628Winch inputs error
  • W8702Power quicktach boom output error active
  • W8703Power quicktach boom output error inactive
  • W8707Power quicktach boom output open circuit
  • W8802Power quicktach boom relay feedback error active
  • W8803Power quicktach boom relay feedback error inactive
  • W8902Power lift output error active
  • W8903Power lift output error inactive
  • W8907Power lift output open circuit
  • W9002Power lift relay error active
  • W9003Power lift relay error inactive
  • W9999Workgroup controller bad table
Looking for a different Bobcat code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Fault code lists by brand