Challenger Rubber Track Tractor Fault Codes List: 04.1.99 to 06.1.98
Page 3 of 18 of the full Challenger Rubber Track Tractor fault code list (1,747 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.
Challenger Rubber Track Tractor codes 04.1.99 to 06.1.98
- 04.1.99Plausibility Error Brake Lever Position
- 04.1.9APlausibility Error in the Determination of the Speed Signal
- 04.1.9BPlausibility Error in the Determination of the Speed Signal
- 04.1.9CTimeout When Closing the Handbrake
- 04.1.9DPlausibility Error Braking System
- 04.1.9EThe Maximum Permissible Brake Pressure in the Handbrake Circuit was Exceeded
- 04.1.A1Twist Angle is not Reached Within 2 Seconds
- 04.1.A2CAN Bus Control Interrupted
- 04.1.A3Incremental Encoder Signal (Actual Position Signal) is Disturbed or Not Logical
- 04.1.A4EST Signal Disturbed or Not Logical
- 04.1.A5Output Reference (= Zero Position) Ignition ON not Found
- 04.1.A6Reference Point Signal During Operation
- 04.1.B0Initialization Error Communication Driver
- 04.1.B1Fatal Error Group Switching
- 04.1.B5Checksum Error Ramp Parameters Fast Recovery for Tractor Management System (TMS)
- 04.1.B7Checksum Incorrect
- 04.1.B8Plausibility Error Between Starter Switch and Clutch Potentiometer
- 04.1.BBError Message "Vehicle Travels Faster Than Allowed End Speed"
- 04.1.BCStep Circuit: Circuit is in Neutral
- 04.1.C3Warning "No Acceleration Allowed by Lever"
- 04.1.C6Warning "Motor Over Speed"
- 04.1.C8Warning "Hand Brake Warning"
- 04.1.CAWarning Message "Give Gas"
- 04.1.CFInternal Error, Operating System A050 Basis
- 04.1.D3Handbrake not Applied (Seat not Occupied, Transmission Active at Standstill) Only for Machines With Seat Switch
- 04.1.D5Communication Errors to the EHR Task
- 04.1.DIWarning "Travel Speed Higher Than Final Speed" (in Emergency Mode)
- 04.1.E2Control Parameters of the Pressure Regulator in the Tensile Force Control are not Plausible or Have Veen Read Incorrectly
- 04.1.E3Checksum Error Parameters for Accelerator Pedal Travel
- 04.1.E4Checksum Error Parameters for Electronic Cardan Brake
- 04.1.E5Checksum Error Range Switching, Speed Limiting Valve, etc. Faulty
- 04.1.E6Checksum Parameter Limit Control Incorrect
- 04.1.E7Checksum Parameter Wrong Control Lever
- 04.1.EAChecksum Incorrect for Parameter Gear Ratios for Gearbox and Gearbox Protection Curve
- 04.1.EBRange Check Sum Incorrect or Range Calibration is Missing
- 04.1.ECFoot Gas Potentiometers: Checksum Faulty or Foot Gas Calibration is Missing
- 04.1.EDClutch Pedal: Checksum Missing or Clutch Calibration Missing
- 04.1.EEML Gearbox Characteristic: Checksum Faulty or Gearbox Calibration Missing
- 04.1.EFTurbo Coupling: Checksum Incorrect/Incorrectly Read or Calibration Missing
- 04.1.ElParameters of the Pulling Force Control Incorrectly Read In
- 04.1.F0Transmission Calibration: Checksum of Parameters Incorrect or Parameter Implausible
- 04.1.F2Deviation Characteristic Offset Outside Permitted Range
- 04.1.F3Translation Limiter: Checksum Incorrect
- 04.1.F4Memory in EXT Could Not be Reserved
- 04.1.F5Checksum Error Parameter "Instance for Selecting the Optimum Speed Source"
- 04.1.F8Checksum Error Parameter Control 4-Wheel Coupling
- 04.1.F9No Specification of Pulling Force via Gearbox
- 04.1.FAChecksum Error Parameter Traction Characteristic
- 04.1.FlStandstill Control: Checksum of Parameters Incorrect
- 04.1.IDPlausibility Error Shutdown Speed
- 04.1.IEPlausibility Error Overspeed
- 04.2.5A100m Calibration: No Pulse From the Radar Sensor During Calibration
- 04.2.9FActivate the "Hand Home" Mode of the Electric Handbrake
- 04.2.A0Electric Parking Brake Can Not be Opened Because the Seat Contact Switch is Not Occupied
- 04.2.BEWarning "Gear Neutral Sleeve"
- 04.2.BFStep Temperature too Low
- 04.2.C0Warning "Seat Switch"
- 04.2.C1Warning "Accelerator ON"
- 04.2.C2Warning "Accelerator OFF"
- 04.2.C5Warning "Activation Button Pressed at Tractor Start"
- 04.2.C7Warning "Active Standstill"
- 04.2.CCBrake Pedal on Pedal Not Adjusted Correctly
- 04.2.CDClutch Pedal Not Calibrated Properly or has Moved
- 04.2.CEWarning "Cruise Control Can not be Activated Because Brake Pedal is Pressed"
- 04.2.D0Workshop Operation: Translation Limiter Active
- 04.2.D2Warning "Steering Column Switch Already Actuated at Tractor Start"
- 04.2.D4Warning "Handbrake Not Tightened Although Seat not Occupied"
- 06.1.01Right fender Button Defective
- 06.1.02Left fender Button Defective
- 06.1.03Control Solenoid Valve Clutch Defective
- 06.1.04PTO Pressure Reducing Valve - Open Circuit or Short to Ground
- 06.1.05PTO Clutch Speed Sensor - Short to Ground
- 06.1.10PTO Clutch Speed Sensor - Short to Power
- 06.1.11Automatic Rear Push Button Defective
- 06.1.13PTO Pressure Reducing Valve - Short to Power
- 06.1.15Button Step Preselection Neutral Defective
- 06.1.16Neutral Button Step Preselection 540 Defective
- 06.1.17Step Button Preselection 540E Defective
- 06.1.18Step Button Preselection 1000 Defective
- 06.1.19Step Button Preselection 1000E Defective
- 06.1.1AValve Stage 540 Defective
- 06.1.1BValve Stage 540E Defective
- 06.1.1CPTO 1000 Solenoid - Short to Power
- 06.1.1DValve Stage 1000E Defective
- 06.1.20Button Stage Preselection 1300 Defective
- 06.1.41OpeRated for More Than 30 Seconds, Mechanical or Electrical Probe Defective
- 06.1.42OpeRated for More Than 30 Seconds, Mechanical or Electrical Probe Defective
- 06.1.43OpeRated for More Than 30 Seconds, Mechanical or Electrical Probe Defective
- 06.1.55Level Selector Button Neutral Pressed for More Than 30 Seconds, Push Button Mechanical or Electrical
- 06.1.56Button Step Preselection 540 Pressed for More Than 30 Seconds, Push Button Mechanical or Electrical
- 06.1.57Button Step Preselection 540E Operated for More Than 30 sec, Push Button Mechanically or Electrically
- 06.1.58Button for Step Preselection 1000 Pressed for More Than 30 Seconds, Push Button Mechanical or Electrical Malfunction
- 06.1.59Button Stage Preselection 1 000E Pressed for More Than 30 Seconds, Push Button Mechanical or Electrical
- 06.1.5AButton Stage Preselection 1000E Pressed for More Than 30 Seconds, Push Button Mechanical or Electrical
- 06.1.60The Actual Speed of the PTO Shaft Deviates by More Than 12% Upwards or Downwards from the Desired Speed of the PTO Clutch
- 06.1.81Counter Button Error Cabin
- 06.1.95Counter Error Neutral
- 06.1.96Counter Error 540
- 06.1.97Counter Error 540E Button
- 06.1.98Counter Error 1000
Other Challenger machine types
Fault code lists by brand
- CAT8,286 codes
- Volvo6,508 codes
- New Holland Tractor3,475 codes
- FPT3,033 codes
- Case IH2,992 codes
- Bobcat2,653 codes
- New Holland Combine2,274 codes
- John Deere Tractors1,884 codes
- Case Wheel Loader1,859 codes
- John Deere Engines1,853 codes
- Cummins1,847 codes
- Volvo Wheel Loader1,726 codes
- Deutz1,684 codes
- Perkins1,523 codes
Safety-critical: confirm before use
Safety first: park on level ground, stop the engine, and secure the machine before any inspection. Thresholds, component locations, wire numbers, fuse locations, and reset procedures can vary by model, configuration, and serial number. Confirm them in the service documentation for your exact machine.