HeavyEquipmentFix
Ask

Challenger Rubber Track Tractor Fault Codes List: 06.1.99 to 0A.1.2B

Page 4 of 18 of the full Challenger Rubber Track Tractor fault code list (1,747 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Challenger Rubber Track Tractor codes 06.1.99 to 0A.1.2B

  • 06.1.99Counter Error 1000E
  • 06.1.9ACounter Error 1300
  • 06.1.A1Communication Error Cab Push Button
  • 06.1.B0Initialization Error Communication Driver Rear PTO Shaft
  • 06.1.B5Communication Error Step Button Pre-Selection Neutral
  • 06.1.B6Communication Error Step Button Preselection 540
  • 06.1.B7Communication Error Step Button Preselection 540E
  • 06.1.B8Communication Error Step Button Preselection 1000
  • 06.1.B9Communication Error Step Button Preselection 1 000E
  • 06.1.BACommunication Error Step Button Preselection 1300
  • 06.1.C0Warning: 540 Stubs at Level 1000 / 1000E
  • 06.1.E0Checksum Parameter Current Control for Stepped Circuit Faulty
  • 06.1.E1Checksum PTO Shaft Parameter Incorrect
  • 06.1.E2Checksum for Pulse Width Increase of the Rear Pinion Shaft Faulty
  • 06.1.E3Checksum for Pulse Width of the Rear Axle Shaft Faulty
  • 06.1.E4Check Sum for Over/ Under Counter of the Rear Axle Shaft Faulty
  • 06.1.E5Checksum for Speed Limit Sensor Faulty After HZW Coupling
  • 06.1.E6Checksum for Pulses Per Revolution with Change Over Stub Faulty
  • 06.1.E7Checksum for Temperature Limits and Switching Times of the HZW Faulty
  • 06.1.E8Checksum for Masks to Show/ Hide the Diagnostics on the PTO Shafts (FZW and HZW) Faulty
  • 08.1.00Unknown Error of the Stern-EHR
  • 08.1.04Pin Configuration Incorrect
  • 08.1.05Checksum/ Equipment Parameter Incorrect
  • 08.1.06Checksum/ Control Parameters Wrong
  • 08.1.07Checksum / WSB Parameters Incorrect
  • 08.1.0AImplausible Configuration
  • 08.1.22The Sensor is Defective
  • 08.1.23The Sensor is Defective
  • 08.1.24The Sensor is Defective
  • 08.1.31Right Bolts Force Measuring Defective
  • 08.1.32Left Pin Force Measuring Defective
  • 08.1.33Right KMB Warning
  • 08.1.34Left KMB Warning
  • 08.1.35Error Detection/ Conditions for VHC Not fulfilled
  • 08.1.38Pressure Sensor (Bearing Side) Defective/ Cable Breakage
  • 08.1.40Rear Lift Defective
  • 08.1.41Left Rear Push Button Defective
  • 08.1.42Right Rear Lift Defective
  • 08.1.43Right Rear Lowering Defective
  • 08.1.44Stop Button Defective
  • 08.1.45TransPort Button Defective
  • 08.1.46Control Button Defective
  • 08.1.47Push Button Quick Release Defective
  • 08.1.48Communication Error of the Rear Hitch Button
  • 08.1.49Valve Defective
  • 08.1.4AValve Defective
  • 08.1.4BAutomatic Rear Lift Button Defective
  • 08.1.4FHKH Key Operation/ Timeout Time
  • 08.1.A2EEPROM Inconsistent (Valve)
  • 08.1.A3RAM Test
  • 08.1.A4Flash Test
  • 08.1.A5Identification Valve (EW / DW) to Selection EOL Wrong
  • 08.1.B0Position Sensor is Not Calibrated
  • 08.1.B2Set Point Potentiometer is Not Calibrated
  • 08.1.B3Foreign Sensor Not Calibrated
  • 08.1.C0MFA Not Available
  • 08.1.C1Terminal Not Available
  • 08.1.CETemperature Limit Warning
  • 08.1.CFTemperature Limit Warning
  • 08.1.F0Valve Does Not RePort on Can
  • 08.1.F2Under Voltage
  • 08.1.F3Over Voltage
  • 08.1.F4Valve Slide Too Short
  • 08.1.F5High Over Voltage
  • 08.1.F6Output Stage Error
  • 08.1.F7Transducer Error
  • 08.1.F8Valve Slide Can Not be Returned in Neutral Position
  • 08.1.F9Valve Slide When Switched on Not in Neutral
  • 08.1.FAValve Slide Too Far Deflected
  • 08.1.FBFloating Position is Not Reached
  • 08.1.FCManual Actuation
  • 08.1.FDPilot Spool Jams
  • 08.1.FFMissing Configuration Message
  • 0A.1.10Electrical Valve 1 - Does Not Report on the CAN
  • 0A.1.11Electrical Valve 1 - EEPROM Inconsistent
  • 0A.1.12Electrical Valve 1 - Undervoltage
  • 0A.1.13Electrical Valve 1 - Overvoltage
  • 0A.1.14Electrical Valve 1 - Valve Slide too Short
  • 0A.1.15Electrical Valve 1 - High Overvoltage
  • 0A.1.16Electrical Valve 1 - Output Stage Error
  • 0A.1.17Electrical Valve 1 - Transducer Error
  • 0A.1.18Electrical Valve 1 - Valve Slide Can Not Be Returned in Neutral Position
  • 0A.1.19Electrical Valve 1 - Valve Slide Can Not Be Returned in Neutral Position
  • 0A.1.1AElectrical Valve 1 - Valve Slide too Far Deflected
  • 0A.1.1BElectrical Valve 1 - Floating Position is Not Reached
  • 0A.1.1CElectrical Valve 1 - Manual Actuation
  • 0A.1.1DElectrical Valve 1 - Steering Slider Clamped
  • 0A.1.1EElectrical Valve 1 - RAM or Flash Test Errors
  • 0A.1.1FElectrical Valve 1 - Missing Set Point Message
  • 0A.1.20Electrical Valve 2 - Does Not Report on the CAN
  • 0A.1.21Electrical Valve 2 - EEPROM Inconsistent
  • 0A.1.22Electrical Valve 2 - Undervoltage
  • 0A.1.23Electrical Valve 2 - Undervoltage
  • 0A.1.24Electrical Valve 2 - Valve Slide Too Short
  • 0A.1.25Electrical Valve 2 - High Over Voltage
  • 0A.1.26Electrical Valve 2 - Output Stage Error
  • 0A.1.27Electrical Valve 2 - Transducer Error
  • 0A.1.28Electrical Valve 2 - Valve Slide Can Not Be Returned in Neutral Position
  • 0A.1.2AElectrical Valve 2 - Valve Slide Too Far Deflected
  • 0A.1.2BElectrical Valve 2 - Floating Position is Not Reached
Looking for a different Challenger Rubber Track Tractor code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Challenger machine types

Fault code lists by brand