HeavyEquipmentFix
Ask

Deutz Fault Codes List: 1161 to 1342

Page 2 of 17 of the full Deutz fault code list (1,684 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Deutz codes 1161 to 1342

  • 1161Zerofuel calibration injector 4 (in firing order); maximum value exceeded
  • 1162Zerofuel calibration injector 5 (in firing order); maximum value exceeded
  • 1163Zero fuel calibration injector 6 (in firing order); maximum exceeded.
  • 1164Zero fuel calibration injector 1 (in firing order); minimum value exceeded.
  • 1165Zero fuel calibration injector 2 (in firing order); minimum value exceeded.
  • 1166Zero fuel calibration injector 3 (in firing order); minimum value exceeded.
  • 1167Zero fuel calibration injector 4 (in firing order); minimum value exceeded.
  • 1168Zero fuel calibration injector 5 (in firing order); minimum value exceeded.
  • 117CAN Message SwtOut (Switching Output): Errormode Not Identifiable
  • 1170Internal software error ECU.
  • 1171Customer oiltemperature: signal unplausible
  • 1172Supply voltage out of range in compressor inlet temperature sensor
  • 1173SCR Tamper detection; derating timer below limit 1
  • 1174SCR Tamper detection; derating timer below limit 2
  • 1175Urea quality; derating timer below limit 1
  • 1176Urea qulaity; derating timer below limit 2
  • 1177Urea tank level; derating timer below limit 1
  • 1178Urea tank level; derating timer below limit 2
  • 118CAN Message "TCO1" (Speedo Signal): Errormode Not Identifiable
  • 1180Physical range check high for battery voltage.
  • 1181Physical range check high for low battery voltage.
  • 1183Air Filter Restriction Sensor Indicates High Restriction
  • 1187Bad quality of reduction agent detected.
  • 1193Physical range check high for exhaust gas temperature upstream turbine.
  • 1194Physical range check low for exhaust gas temperature upstream turbine.
  • 12Analog Accelerator Pedal Sensor 1 Or Double Accelerator Pedal Sensor: Erratic, Intermittent Or Incorrect
  • 120CAN Message TSC1 - AE (Torque/Speed Control #1 From Automatic Traction Control To Engine): Errormode Not Identifiable
  • 1209Exhaust back pressure data irregular or not calculable
  • 121CAN Message TSC1-AR (Torque/Speed Control) #1 From Automatic Traction Control To Retarder: Errormode Not Identifiable
  • 1219HMI engine derate service state DPF wasn’t regenerated, power reduction phase 1 ( regeneration request).
  • 122CAN Message TSC1-DE (Torque/Speed Control #1 From Driveline to Engine): Errormode Not Identifiable
  • 1220HMI engine derate service state DPF wasn’t regenerated, power reduction phase 2 ( regeneration request).
  • 1222Camshaft- and Crankshaft speed sensor signal not available on CAN.
  • 1223Actuator EGR-Valve (2.9;3.6) or Throttle-Valve (4.1;6.1;7.8) open load.
  • 1224Actuator EGR-Valve (2.9;3.6) or Throttle-Valve (4.1;6.1;7.8) high current.
  • 1226EGR-Valve (2.9;3.6) or Throttle-Valve (4.1;6.1;7.8) short circuit to battery.
  • 1227EGR-Valve (2.9;3.6) or Throttle-Valve (4.1;6.1;7.8) short circuit to battery.
  • 1228EGR-Valve (2.9;3.6) or Throttle-Valve (4.1;6.1;7.8) short circuit to ground.
  • 1229EGR-Valve (2.9;3.6) or Throttle-Valve (4.1;6.1;7.8) short circuit to ground.
  • 123CAN Message TSC1-DR (Torque/Speed Control #1 From Driveline to Retarder): Errormode Not Identifiable
  • 1230Actuator error EGR-Valve (2.9;3.6) or Throttle-Valve (4.1;6.1;7.8); overload by short circuit.
  • 1231Actuator error EGR-Valve (2.9;3.6) or Throttle-Valve (4.1;6.1;7.8); Power stage overtemperature due to high current 3.6) Drosselklappe (4.1;6.1;7.8); Leistungsstufe Übertemperatur durch zu hohen Storm;
  • 1232Actuator error EGR-Valve (2.9;3.6) or Throttle-Valve (4.1;6.1;7.8); Voltage below threshold 3.6) Drosselklappe (4.1;6.1;7.8); Spannung unter Grenzwert;
  • 1235ECU CAN 3 short circuit.
  • 1239UB7; Short circuit to battery error of actuator relay 7.
  • 124CAN Message TSC1-PE (Torque/Speed Control #1 From Power Take Off To Engine): Errormode Not Identifiable
  • 1241Relays SCR-Heater, Short Circuit to Ground (High side Control side)
  • 1242UB7; Short circuit to ground actuator relay 7
  • 1247Burner Control; Air Line - Blocked Air Pump; Air lines blocked.
  • 1248Burner Control; Air Pump - CAN Lost Air Pump; CAN communication lost.
  • 1249Air pump; CAN communication interrupted no purge function available.
  • 125CAN Message TSC1 - TE (Torque/Speed Control #1 From Traction Control to Engine): Errormode Not Identifiable
  • 1250Air pump; Internal error.
  • 1252Air pump; operating voltage error.
  • 1254Air inlet EPV - pressure too low. Air pressure glow plug flush line; below limit.
  • 1255Burner Control; Flame lost max. Burner operation is interrupted too often.
  • 1257HCI dosing valve (DV1); blocked open.
  • 1258Burner Control; HFM-Electrical Fault. HFM sensor; electrical fault.
  • 1259Burner Control; HFM-Pausibilitatsfehler 1 Amount of air is not plausible to pump speed.
  • 126CAN Message TSC1-TR (Torque/Speed Control #1 From Traction Control To Retarder): Errormode Not Identifiable
  • 1261Burner Control Air Pump; over current. Air pump electrically overloaded.
  • 1262Burner Control; Shut-off Valve - Blocked closed. Burner Shut Off Valve; blocked closed.
  • 1263Burner Control; Fuel line ShutOff downstream - broken. Burner fuel line pipe leak behind Shut Off Valve.
  • 1264Burner Control; Shut Off Valve; Blocked Open
  • 127DLC Error of CAN-Receive-Frame AT1IG1 NOX Sensor (SCR-system upstream cat; DPF-system downstream cat); length of frame incorrect
  • 128CAN Message TSC1-VR (Torque/Speed Control #1 From Vehicle Control To Retarder): Errormode Not Identifiable
  • 1285Timeout error of CAN-Receive-Frame ComMS_Sys1TO (error memory slave); Master-slave internal CAN message.
  • 1286Timeout error of CAN-Receive-Frame ComMS_Sys2TO (error memory slave); Master-slave internal CAN message.
  • 1287Timeout error of CAN-Receive-Frame ComMS_Sys3TO (error memory slave); Master-slave internal CAN message.
  • 1288Timeout error of CAN-Receive-Frame ComMS_Sys4TO (error memory slave); Master-slave internal CAN message.
  • 1289Timeout error of CAN-Receive-Frame ComMS_Sys5TO (error memory slave); Master-slave internal CAN message.
  • 129DLC error of CAN-receive-frame AT1IG1Vol NOX sensor.
  • 1290Timeout error of CAN-Receive-Frame ComMS_Sys6TO (error memory slave); Master-slave internal CAN message
  • 1291Master Slave, Error of message counter CAN receive message ComMSMoFOvR; ComMSMoFOvR1CNT
  • 1292Master - Slave CAN; Error Checksum of CAN-Receive Message
  • 1293Master-Slave CAN; Error of message length of CAN receive message ComMSMoFOvR; ComMSMoFOvR1DLC.
  • 1294Timeout error CAN message ComMSMoFOvR1TO error memory slave.
  • 1299Wastegate plausibility error off CAN transmit message
  • 13DEF downstream line heater current below normal or open circuit
  • 130Timeout error of CAN-receive-frame AT1IG1Vol; NOX sensor.
  • 1300Timeout Error of CAN-Receive-Frame ComTrbChActr; Wastegate.
  • 1302Deviation of the exhaust gas temperature setpoint to actuator value downstream (DOC) too high.
  • 131CAN Message: Errormode Not Identifiable
  • 1324Check of missing injector adjustment value programming (IMA) Injector 7 (in firing order).
  • 1325Check of missing injector adjustment value programming (IMA) Injector 8 (in firing order).
  • 1326Injector cylinder bank 1 slave; short circuit.
  • 1327Injector cylinder bank 2 slave; short circuit.
  • 1328Injector powerstage output slave defect.
  • 1329Injector 7 (in firing order); interruption of electric connection.
  • 133Timeout error (BAM to packet) for CAN-receive-frame AT1IGCVol1.
  • 1330Injector 8 (in firing order); interruption of electric connection.
  • 1333Injection 7 (in firing order); short circuit.
  • 1334Injector 8 (in firing order); short circuit.
  • 1337Timeout Of Short-Circuit Ground Diagnosis Cycle. Bank 0; IVDiaSHCirnd ToutBnk_0
  • 1338Timeout Of Short-Circuit Ground Diagnosis Cycle. Bank 1; IVDiaSHCirnd ToutBnk_0
  • 1339Injector Diagnostic; Short Circuit To Ground Cylinder Bank 0
  • 134Broadcast announce message of the calibration message of the upstream catalytic NOx sensor has failed.
  • 1340Injector Diagnostic; Short Circuit To Ground Cylinder Bank 1
  • 1341Injector diagnostics; time out error in the SPI communication.
  • 1342Injector diagnostics Slave; time out error in the SPI communication.
Looking for a different Deutz code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Deutz machine types

Fault code lists by brand