FPT Fault Codes List: E8DD to F39F-0
Page 29 of 31 of the full FPT fault code list (3,033 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.
FPT codes E8DD to F39F-0
- E8DDECU Internal Failure - Torque Request Due to fuel Pressure Exceeds Maximum Torque Limit
- E8DD-0ECU Internal
- E8DD-1FECU Internal
- E91DECU Internal Failure - 'ABE Active' Reported Due to Undervoltage Detection
- E91D-0ECU Internal
- E91D-1FECU Internal
- E92DInternal 12V Supply Voltage is Too Low
- E92D-0ECU Voltage Supply
- E92D-1FECU Voltage Supply
- E98EUpstream NOx Sensor Values Are Not Plausible
- E98E-0NOx Sensor (CAN)
- E9DDECU Internal Failure - Torque Request Due to Air Control Exceeds Maximum Torque Limit
- E9DD-0ECU Internal
- E9DD-1FECU Internal
- E9DENH3 Sensor Open in Heater Circuit Causing Underheating
- E9DE-0NH3 Sensor
- E9DE-1FNH3 Sensor
- EAFunctionality 3 (Plausibility Checks) - Pressure Line Blocked
- EA1DECU Internal Failure - 'ABE Active' Reported Due to Overvoltage Detection
- EA1D-0ECU Internal
- EA1D-1FECU Internal
- EADDECU Internal Failure - Torque Request Exceeds Maximum Torque Limit
- EADD-0ECU Internal
- EADD-1FECU Internal
- EADENH3 Sensor Open or Short in Temperature Cell Circuit
- EADE-0NH3 Sensor
- EADE-1FNH3 Sensor
- EBFunctionality 3 (Plausibility Checks) - Low Urea Level 1 (Warning)
- EB1DECU Internal Failure - 'WDA, ABE Active' Reported
- EB1D-0ECU Internal
- EB1D-1FECU Internal
- EBDDECU 5 Volt Supply Voltage is Higher Than Expected
- EBDD-0ECU Voltage Supply
- EBDD-1FECU Voltage Supply
- EBDENH3 Sensor Open or Short in Trim Resistor Circuit
- EBDE-0NH3 Sensor
- EBDE-1FNH3 Sensor
- ECFunctionality 3 (Plausibility Checks) - Low Urea Level 2 (Warning)
- EC36ECU Internal Failure - Fuel Injection Energizing Time is Not Plausible
- EC36-0ECU Internal Check
- EC36-1FECU Internal Check
- ECDDECU 5 Volt Supply Voltage is Lower Than Expected
- ECDD-0ECU Voltage Supply
- ECDD-1FECU Voltage Supply
- ED1DECU Internal Failure - Software Resets in DSM 0
- ED1D-0ECU SW Reset
- ED1D-1FECU SW Reset
- ED2DCAN Communication Failure - External Torque or Speed Checksum and Counter
- ED2D-0CAN Bus
- ED36ECU Internal Failure - Fuel Injection Energizing Phase is Not Plausible
- ED36-0ECU Internal
- ED36-1FECU Internal
- EE1DECU Internal Failure - Software Resets in DSM 1
- EE1D-0ECU SW Reset
- EE1D-1FECU SW Reset
- EE36-0Injector Adjustment
- EE36-1FECU Internal
- F0OBD/NOx - Group Error Path Urea Injection Control
- F1OBD/NOx - Group Error Path Air Control
- F11FSCR Inducement Warning Due To Distance Time is Active - Level 1
- F11F-0SCR Inducement
- F15FSCR Inducement Warning Due to Distance or Time is Active - Level 2
- F15F-0SCR Inducement
- F167FSCR Inducement Warning Due to Distance or Time is Active - Level 4
- F16FSCR Inducement Warning Due to Distance Time is Active - Level 3
- F16F-0SCR Inducement
- F176-0Injector Adjustment
- F176-1FInjector Adjustment
- F17F-0SCR Inducement
- F18FDEF Level Too Low Warning is Active - Stage 1
- F18F-0SCR Reagent Tank Level
- F18F-1FSCR Reagent Tank Level
- F19F-0SCR Inducement
- F19F-1FSCR Inducement
- F1A2Engine Over Speed Condition Detected
- F1A2-0Engine Overspeed
- F1A2-1FEngine Overspeed
- F1EFTorque Limitation Caused By Turbo Charger Protection
- F1EF-0Info: Torque Limitation Active
- F1EF-1FInfo: Torque Limitation Active
- F2OBD/NOx - Group Error Path Catalyst Temperature
- F245Fuel Pressure Relief Valve is Forced to Open, Perform Pressure Increase
- F245-0Pressure Relieve Valve
- F245-1FPressure Relieve Valve
- F276-0Injector Adjustment
- F276-1FInjector Adjustment
- F28FDEF Level Too Low Warning is Active - Stage 2
- F28F-0SCR Reagent Tank Level
- F28F-1FSCR Reagent Tank Level
- F29F-0SCR Inducement
- F29F-1FSCR Inducement
- F2EFStrong Torque Limitation From Engine Protection Active
- F2EF-0Info: Torque Limitation Active
- F2EF-1FInfo: Torque Limitation Active
- F345Fuel Pressure Relief Valve is Forced to Open, Perform Pressure Shock
- F345-0Pressure Relieve Valve
- F345-1FPressure Relieve Valve
- F376-0Injector Adjustment
- F376-1Finjector Adjustment
- F39F-0SCR Inducement
Fault code lists by brand
- CAT8,286 codes
- Volvo6,508 codes
- New Holland Tractor3,475 codes
- Case IH2,992 codes
- Bobcat2,653 codes
- Challenger Tractor2,434 codes
- New Holland Combine2,274 codes
- John Deere Tractors1,884 codes
- Case Wheel Loader1,859 codes
- John Deere Engines1,853 codes
- Cummins1,847 codes
- Challenger Rubber Track Tractor1,747 codes
- Volvo Wheel Loader1,726 codes
- Deutz1,684 codes
Safety-critical: confirm before use
Safety first: park on level ground, stop the engine, and secure the machine before any inspection. Thresholds, component locations, wire numbers, fuse locations, and reset procedures can vary by model, configuration, and serial number. Confirm them in the service documentation for your exact machine.