HeavyEquipmentFix
Ask

New Holland Tractor Fault Codes List: FD9F to U77

Page 35 of 35 of the full New Holland Tractor fault code list (3,475 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

New Holland Tractor codes FD9F to U77

  • FD9FSCR Inducement: Level 1 (Torque Reduction), Triggered by Tampering Fault
  • FE9FSCR Inducement: Level 3 (Creep Mode) Triggered by Tampering Fault
  • FEBADefective Pressure Reduction
  • FF9FSCR Inducement: Warning, Triggered by Tampering Fault
  • FIEFTorque Limitation Caused by Turbo Charger Protection
  • SPN 3038Constant Engine Speed Selector Switch - Signals Not Plausible
  • SPN 3157Engine Control Unit (ECU) Not Detected on the CANbus or the Engine Dataset Registration Information Was Not Available from the Engine within the Time Required
  • SPN 3158Invalid ECM Checksum (the Engine Dataset Does Not Match the Dataset Registered for This Machine
  • SPN 3159Invalid Engine Reference Torque
  • SPN 3375Constant Engine Speed Increase/Decrease Switch - Signals Not Plausible
  • SPN 3377CRPM Switches Present but Function Not Enabled
  • SPN 3983Engine Overspeed Detected
  • SPN 3999Unknown ECU Error Code
  • U01Front Axle Potentiometer Open Circuit - ACP Will Not Work
  • U02Front Axle Potentiometer Threshold is Higher Than Set Limit
  • U03Front Axle Potentiometer Short Circuit - ACP Will Not Work
  • U04Front Axle Potentiometer Threshold is Lower Than Set Limit
  • U05Suspension is Not Reaching its Minimum/Maximum Position During ACP Procedure
  • U07Suspension is Stationary During the Raise Command in the ACP Procedure
  • U08Suspension Unable to Reach Maximum Height within 20 Seconds
  • U09Suspension is Stationary During the Lowering Command in the ACP Procedure
  • U10Suspension Unable to Reach Minimum Height within 25 Seconds
  • U11Unable to Calibrate Suspension
  • U110Position Potentiometer Value Too High or the Hitch is Not Lowered - Calibration Fault
  • U111Position Potentiometer Value Too High or the Hitch is Not Lowered - Calibration Fault
  • U112PTO Speed Select Cable Stalled While Extending
  • U113PTO Speed Select Cable Stalled While Retracting
  • U114Hand Brake Applied - Calibration Fault
  • U115Shuttle Lever Not in the Park Position - Calibration Fault
  • U116APR Position Too High - Calibration Fault
  • U117APR Position Too Low - Calibration Fault
  • U118Error Codes Active Preventing Completion of Initialization Procedure - Calibration Fault
  • U119Bowden Cable Not Connected - Calibration Fault
  • U12ACP Stopped, Vehicle Not Stationary
  • U120Inclinometer Self Test Failed - Calibration Fault
  • U121Inclinometer Calibration Procedure Not Ok
  • U122Inclinometer Offset Out of Range - Calibration Fault
  • U124PTO Speed Select Switch in Optional Speed Position
  • U125Speed Sensor Error
  • U126No Movement from Position Sensor
  • U13Valve 30 (Upper Lockout) Solenoid Open Circuit
  • U14Valve 31 (Lower Lockout) Solenoid Open Circuit
  • U15Valve 30 (Upper Lockout) and Valve 31 (Lower Lockout) Solenoid Connectors Swapped
  • U16Valve 30 (Upper Lockout) and Valve 31 (Lower Lockout) Current Sense Inputs Swapped
  • U17Seat Switch Not Activated - Calibration Fault
  • U18Front Suspension Pressure Switch Short Circuit
  • U19Oil Temperature <10°C, Calibration is Not Possible
  • U20Handbrake is Not Set - Calibration Fault
  • U21ERPM is Below 1300, Increase Throttle - Calibration Fault
  • U22ERPM is Above 1350, Reduce Throttle - Calibration Fault
  • U23Shuttle Lever is in Neutral, Shift it to Forward - Calibration Fault
  • U24lncorrect Range Selected
  • U26Clutch Pedal is Not Up, Release Clutch Pedal - Calibration Fault
  • U31Wheel Speed Sensed - Tractor Moving - Calibration Fault
  • U36Max Allowed Clutch Calibration Value Exceeded
  • U51Engine Speed Error
  • U52Constant ERPM Switch Detected
  • U55PTO Started
  • U58PTO Twist Sensor Open Circuit
  • U59PTO Twist Sensor Short Circuit
  • U61Lever No.1 Not in Neutral - Calibration Fault
  • U62Lever No.2 Not in Neutral - Calibration Fault
  • U63Lever No.3 Not in Neutral - Calibration Fault
  • U64Lever No.4 Not in Neutral
  • U68Creeper Not Engaged - Calibration Fault
  • U69Creeper Stuck - Calibration Fault
  • U70PTO Twist Sensor Not Calibrated
  • U71Calibration Attempted While Enable Switch is Off - Calibration Fault
  • U72Proximity Sensor Input is Out of Range - Open - Calibration Fault
  • U73Proximity Sensor Input is Out of Range - Closed - Calibration Fault
  • U74LVDT Calibration Has Been Unsuccessful (Out of Range After 4th Attempt)
  • U75Quick Fill Calibration Value Too High
  • U76Quick Fill Calibration Value Too Low
  • U77Damper Calibration Value Too High
Looking for a different New Holland Tractor code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other New Holland machine types

Fault code lists by brand