Volvo Fault Codes List: PPID 34 FMI 1 to PSID 10 FMI 12
Page 48 of 65 of the full Volvo fault code list (6,446 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.
Volvo codes PPID 34 FMI 1 to PSID 10 FMI 12
- PPID 34 FMI 1ECU+12V Output
- PPID 35 FMI 0EGR Mass Flow - Data valid but above normal operational range - most severe level
- PPID 35 FMI 1EGR Mass Flow - Data valid but below normal operational range - most severe level
- PPID 35 FMI 3EGR Mass Flow Sensor
- PPID 35 FMI 4EGR Mass Flow Sensor
- PPID 35 FMI 5EGR Mass Flow Sensor
- PPID 35 FMI 9EGR Mass Flow Sensor
- PPID 387 FMI 10Temperature Sensor, Catalytic Converter - Abnormal rate of change
- PPID 387 FMI 2Temperature Sensor, Catalytic Converter - Data erratic, intermittent or incorrect
- PPID 387 FMI 4Temperature Sensor, Catalytic Converter - Voltage below normal or shorted low
- PPID 387 FMI 5Temperature Sensor, Catalytic Converter - Current below normal or open circuit
- PPID 3 FMI 3Starter Output
- PPID 3 FMI 4Starter Output
- PPID 3 FMI 5Starter Output
- PPID 42 FMI 12Transmission Status
- PPID 430 FMI 0Regeneration Volume
- PPID 436 FMI 10Exhaust Gas Temperature Sensor 3 - Abnormal rate of change
- PPID 436 FMI 2Exhaust Gas Temperature Sensor 3 - Data erratic intermittent or incorrect
- PPID 436 FMI 4Exhaust Gas Temperature Sensor 3 - Voltage below normal or shorted low
- PPID 436 FMI 5Exhaust Gas Temperature Sensor 3 - Current below normal or open circuit
- PPID 437 FMI 10Aftertreatment Injector Fuel Pressure Sensor - Abnormal rate of change
- PPID 437 FMI 2Aftertreatment Injector Fuel Pressure Sensor - Data erratic intermittent or incorrect
- PPID 437 FMI 3Aftertreatment Injector Fuel Pressure Sensor - Voltage above normal or shorted to high source
- PPID 437 FMI 5Aftertreatment Injector Fuel Pressure Sensor - Current below normal or open circuit
- PPID 50 FMI 0Clutch, Pre-load - Data valid but above normal operational range
- PPID 50 FMI 1Clutch Load on Plate
- PPID 50 FMI 11Clutch, Pre-load - Clutch protection active (unidentifiable error)
- PPID 50 FMI 14Clutch, Pre-load - Special instructions
- PPID 50 FMI 2Clutch Load on Plate
- PPID 51 FMI 13Clutch Disc, Pull Position - Calibration value out of range
- PPID 54 FMI 0ECU +5V Output - Data valid but above normal operational range
- PPID 54 FMI 1ECU +5V Output - Data valid but below operational range
- PPID 55 FMI 0ECU, Temperature - Data valid but above normal operational range
- PPID 55 FMI 1ECU Temperature
- PPID 55 FMI 14ECU Temperature
- PPID 55 FMI 2ECU Temperature
- PPID 55 FMI 4ECU Temperature
- PPID 55 FMI 5ECU Temperature
- PPID 59 FMI 2Pushbutton Backlighting Status
- PPID 59 FMI 3Pushbutton Backlighting Status
- PPID 60 FMI 2Accelerator Pedal Switches
- PPID 60 FMI 3Idle Validation Switch Supply
- PPID 60 FMI 4Idle Validation Switch Supply
- PPID 60 FMI 7Accelerator Pedal Switches
- PPID 61 FMI 7Engine Brake Switch - Mechanical system not responding or out of adjustment
- PPID 69 FMI 3Buffered Idle Validation Switch - Voltage above normal, or shorted to high source
- PPID 69 FMI 4Buffered Idle Validation Switch - Voltage below normal, or shorted to low source
- PPID 70 FMI 4Pedal Switches, Supply - Voltage below normal, or shorted to low source
- PPID 71 FMI 4Cruise Control and Engine Brake, Switch Supply - Voltage below normal or shorted to low source
- PPID 72 FMI 3Accelerator Pedal and Engine Brake, Sensors Supply - Voltage above normal or shorted to high source
- PPID 72 FMI 4Accelerator Pedal and Engine Brake, Sensors Supply - Voltage below normal or shorted to low source
- PPID 73 FMI 3Second Accelerator Pedal, Supply Sensors - Voltage above normal, or shorted to high source
- PPID 73 FMI 4Second Accelerator Pedal, Supply Sensors - Voltage below normal, or shorted to low source
- PPID 74 FMI 3EECU/VECU Supply Relay
- PPID 74 FMI 4EMS / VECU Supply Voltage
- PPID 75 FMI 3Range Inhibitor Solenoid Valve
- PPID 75 FMI 4Range Inhibitor Solenoid Valve
- PPID 77 FMI 3Compressor Control
- PPID 77 FMI 4Compressor Control
- PPID 79 FMI 3Area Inhibitor Solenoid Valve
- PPID 79 FMI 4Area Inhibitor Solenoid Valve
- PPID 86 FMI 9Engine Retarder Percent
- PPID 89 FMI 0Variable Geometry Turbocharger Smart Remote Actuator Temperature - Data valid but above normal operational range - most severe level
- PPID 90 FMI 2Transmission Range Status
- PPID 90 FMI 3Transmission Range Status
- PPID 90 FMI 7Transmission Range Status
- PPID 91 FMI 9Brake Third Pressure
- PPID 92 FMI 0Engine Fan Hydraulic Level
- PPID 92 FMI 1Engine Fan Hydraulic Oil filter
- PPID 92 FMI 11Slipping Brake/Clutch
- PPID 92 FMI 3Solenoid Valve S8 Reverse Clutch
- PPID 92 FMI 4Solenoid Valve S8 Reverse Clutch
- PPID 92 FMI 5Solenoid Valve S8 Reverse Clutch
- PPID 92 FMI 7Slipping Lockup Clutch
- PPID 93 FMI 0Engine Fan Hydraulic Oil filter
- PSID 100 FMI 2Gear Selector
- PSID 100 FMI 7Gear Selector
- PSID 102 FMI 6Solenoid Valve S8 Reverse Clutch
- PSID 103 FMI 3Solenoid Valve S11 Main Pressure
- PSID 103 FMI 4Solenoid Valve S11 Main Pressure
- PSID 103 FMI 5Solenoid Valve S11 Main Pressure
- PSID 103 FMI 6Solenoid Valve S11 Main Pressure
- PSID 104 FMI 5Solenoid Valve S13 Brake Pressure
- PSID 105 FMI 3Solenoid Valve Power Take Off
- PSID 105 FMI 4Solenoid Valve Power Take Off
- PSID 105 FMI 5Solenoid Valve Power Take Off
- PSID 105 FMI 6Solenoid Valve Power Take Off
- PSID 107 FMI 11Input/Output Shaft
- PSID 108 FMI 0Shift Elements
- PSID 108 FMI 11Shift Elements
- PSID 108 FMI 7Aftertreatment Injector System - Mechanical system not responding, or out of adjustment
- PSID 109 FMI 11Input Shaft Sensor
- PSID 109 FMI 12Engine Coolant Temperature Sensor - Thermostat blocked open
- PSID 109 FMI 2Input Shaft Sensor
- PSID 109 FMI 3Input Shaft Sensor
- PSID 109 FMI 4Input Shaft Sensor
- PSID 109 FMI 5Input Shaft Sensor
- PSID 109 FMI 7Engine Coolant Temperature Sensor - Thermostat blocked closed
- PSID 109 FMI 8Input Shaft Sensor
- PSID 10 FMI 12Sensor Element (SEG1)
Other Volvo machine types
Fault code lists by brand
- CAT8,255 codes
- New Holland Tractor3,475 codes
- FPT3,033 codes
- Case IH2,992 codes
- Bobcat2,653 codes
- Challenger Tractor2,434 codes
- New Holland Combine2,274 codes
- John Deere Tractors1,884 codes
- Case Wheel Loader1,860 codes
- John Deere Engines1,853 codes
- Cummins1,847 codes
- Challenger Rubber Track Tractor1,747 codes
- Deutz1,684 codes
- Perkins1,522 codes
Safety-critical: confirm before use
Safety first: park on level ground, stop the engine, and secure the machine before any inspection. Thresholds, component locations, wire numbers, fuse locations, and reset procedures can vary by model, configuration, and serial number. Confirm them in the service documentation for your exact machine.