HeavyEquipmentFix
Ask

Bobcat Fault Codes List: P2670 to U1096-08

Page 20 of 24 of the full Bobcat fault code list (2,653 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Bobcat codes P2670 to U1096-08

  • P2670ECU sensor supply 2 low range fault
  • P2671ECU sensor supply 2 high range fault
  • P2684ECU sensor supply 3 short to ground
  • P2685ECU sensor supply 3 low range fault
  • P2686ECU fault code P2686 detected
  • P3002Exhaust temperature extremely high.
  • P3003Exhaust temperature extremely high.
  • P3004Exhaust temperature extremely high.
  • P3006Particulate matter warning.
  • P3007Particulate matter high.
  • P3008Particulate matter extremely high.
  • P3011Boost pressure fault detected.
  • P3012Low water temperature in parked regeneration.
  • P3013Parked regeneration time out.
  • P3018Exhaust temperature sensor fault detected.
  • P3019Pump calibration error.
  • P3023Exhaust gas temperature sensor fault detected.
  • P3024DPF fault detected.
  • P3025Water temperature sensor fault detected.
  • P3052DPF differential pressure sensor fault detected.
  • P3611DPF regeneration active lamp short to battery.
  • R3327IQ Touch CAN error.
  • R3334IQ Touch CAN RX error.
  • R3335IQ Touch CAN TX error.
  • R3904Jog shuttle no communication.
  • R4304Keyless start panel no communication.
  • R7404Main Controller No Communication
  • R7492Main controller authentication failed.
  • T9002Service Tool Output ‘C’ Error On
  • T9003Service Tool Output ‘C’ Error Off
  • T9102Service Tool Output ‘D’ Error On
  • T9103Service Tool Output ‘D’ Error Off
  • T9202Service Tool Output ‘E’ Error On
  • T9203Service Tool Output ‘E’ Error Off
  • T9302Service Tool Output ‘F’ Error On
  • T9303Service Tool Output ‘F’ Error Off
  • U0028ECU CAN communication fault.
  • U0029ECU CAN communication fault.
  • U0075ECU communication error.
  • U0076EGR Fault
  • U0077ECU communication fault.
  • U0081ECU Communication Error
  • U0082ECU Communication Fault
  • U0083ECU Communication Fault
  • U0084ECU Communication Fault
  • U0085ECU Communication Fault
  • U0086ECU Communication Fault
  • U0087ECU Communication Fault
  • U0089ECU Communication Fault
  • U0100ECU Communication Fault
  • U0140Throttle Position Sensor Fault
  • U0401DCU Communication Fault
  • U0606ECU CAN Communication Fault - Engine Speed Control
  • U0607ECU CAN Communication Fault
  • U0608ECU CAN Communication Fault - Engine Speed Control
  • U0619ECU CAN communication fault - DEF sensor.
  • U0632ECU CAN communication fault - cooling fan control.
  • U1001CAN communication fault - hydraulic oil temperature.
  • U1003Received engine shutdown request from machine controller.
  • U1010-08PTOL Keypad No Communication
  • U1011-08Options Keypad No Communication
  • U1012-08Cab Keypad No Communication
  • U1013-08Accessory keypad no communication.
  • U1015-62Throttle encoder signal compare failure.
  • U1024NOx pre-treatment CAN communication fault.
  • U1025NOx pre-treatment CAN communication fault.
  • U1026NOx pre-treatment CAN communication fault.
  • U1027NOx pre-treatment CAN communication fault.
  • U1028NOx pre-treatment CAN communication fault.
  • U1029NOx pre-treatment CAN communication fault.
  • U1030Nox Post-Treatment CAN Communication Fault
  • U1031Nox Post-Treatment CAN Communication Fault
  • U1032ECU CAN communication fault - PTO.
  • U1033ECU CAN communication fault - starter relay.
  • U1050-00Hub controller interrupted power failure.
  • U1051-00Cab controller interrupted power failure.
  • U1053-00Drive controller interrupted power.
  • U1054-00Interrupted power failure.
  • U1055-00Aux controller interrupted power failure.
  • U1056-00Rear auxiliary controller interrupted power failure.
  • U1060-46Workgroup calibration failed.
  • U1060-87Workgroup calibration required.
  • U1075-00Lights controller interrupted power failure.
  • U1090-51Hub controller not programmed.
  • U1090-57Hub controller incompatible software component.
  • U1091-08Display bus signal/message failure.
  • U1091-51Display not programmed.
  • U1092-08Cab controller bus signal/message failure.
  • U1092-51Cab controller not programmed.
  • U1092-57Cab controller incompatible software component.
  • U1093-08Mid controller no communication.
  • U1093-51Mid controller not calibrated.
  • U1093-57Mid controller software version error.
  • U1094-08Drive controller no communication.
  • U1094-51Drive controller not programmed.
  • U1094-57Drive controller software update required.
  • U1095-08Workgroup controller no communication.
  • U1095-51Workgroup controller not programmed.
  • U1095-57Workgroup controller software version error.
  • U1096-08ECU bus signal/message failure.
Looking for a different Bobcat code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Fault code lists by brand