HeavyEquipmentFix
Ask

Case IH Fault Codes List: 2558 to 3012

Page 11 of 30 of the full Case IH fault code list (2,992 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Case IH codes 2558 to 3012

  • 2558Hydro 1 Solenoid - Short Circuit To 12V
  • 2559ORPM And Ring Fault
  • 2560Uncommand Movement Of Synchronizer F1/F3 To Neutral
  • 2561Uncommand Movement Of Synchronizer F2/R1 To Neutral
  • 256EUpstream NOx Sensor Internal Failure (Heater Short Circuit Error)
  • 2582Left Brake Pedal Switch Fault - Electrical Signals Are Inconsistent
  • 2583Right Brake Pedal Switch Fault - Electrical Signals Are Inconsistent
  • 26Blower Motor Short Circuit
  • 2600Variator Solenoid Open Circuit or Shorted to Ground
  • 2601Variator Solenoid 12 Volt Circuit Error
  • 2602Variator Not Calibrated
  • 2603Variator Control Valve Stuck
  • 2605Transmission Speed Pedal Potentiometer Shorted to Ground or Open Circuit
  • 2606Transmission Speed Pedal Potentiometer 5V or 12V Circuit Error
  • 2607Transmission Speed Pedal Neutral Switch Error
  • 2610Variator Drive Slipping
  • 2615Transmission Torque Pressure Sensor Open Circuit or Shorted to Ground
  • 2616Transmission Torque Pressure Sensor Shorted to 5V or 12V
  • 2620Input Pulley Speed Sensor Shorted to 12V or Open Circuit
  • 2621Input Pulley Speed Sensor Shorted to Ground
  • 2630Output Pulley Speed Sensor Shorted to 12V or Open Circuit
  • 2631Output Pulley Speed Sensor Shorted to Ground
  • 2640Transmission Standstill Solenoid Open Circuit or Shorted to Ground
  • 2641Transmission Standstill Solenoid Shorted to 12V
  • 2650CVT Pressure Switch Error
  • 26AADEF Temperature Sensor Voltage is Lower Than Expected
  • 26D3Oil Pressure is Too Low
  • 27Blower Motor Disconnected
  • 2700Engine Speed Sensor Shorted to 12V or Open Circuit
  • 2701Engine Speed Sensor Shorted to Ground
  • 2702Engine Speed CAN Message Not Received
  • 271ADownstream SCR Catalyst Temperature Sensor Voltage is Lower Than Expected
  • 275DECU Temperature Sensor Voltage is Lower Than Expected
  • 2765Fuel Rail Pressure Has Exceeded Minimum Limit
  • 28Relay First Speed Short Circuit
  • 2800Auto Guidance Isolation Valve Driver Fault
  • 2805System Pressure Valve Solenoid Circuit Is Open Circuit Or Shorted To Ground
  • 2806System Pressure Solenoid Is Shorted To B+
  • 2807Transmission Output Rpm Over Speed
  • 2809The Battery Voltage Is Too Low To Permit Operation Of the Clutch Solenoids.
  • 2811Transmission Oil Temperature Hot
  • 2812Transmission Oil Temperature Sensor Short To B+ Or Open Circuit
  • 2813Transmission Oil Temperature Sensor Short To Ground
  • 2814Integrated Control Panel Off Line
  • 2815Governor Engine RPM Alternator Engine RPM Mismatch
  • 2816Transmission Regulated Pressure Accumulator Is Flat
  • 2817Governor Is Offline CAN Bus
  • 2818Communication Lost With the Armrest Control Module (ACM)
  • 2819Communication Lost With the Instrumentation Controller.
  • 2820System Pressure Low Possible System Pressure Hydraulic Pump Failure Or Leak
  • 2821System Pressure Low Fault
  • 2850The Park Brake Is Stuck On By No Electrical Power Supplied When Commanded On
  • 2851The Park Brake Driver Has Detected An Over Current Or An Open Circuit Condition.
  • 2852The Park Brake Is Stuck On By No Electrical Power Supplied To the Solenoid When Driver Is Commanded On. Possible Service Brake Bottom Brake Switches Open.
  • 2858Exhaust Gas Pressure Sensor Voltage is Lower Than Expected
  • 2873Software Is Out Of the Calibration Mode And The Park Brake Request Is Still Active. If This Fault Is Detected There Is A Bug In the Software.
  • 2874The Park Brakes Commanded On and Gear Is Engaged And There Is No Park Brake Request From Calibration. If This Fault Is Detected There Is A Bug In The Software.
  • 28AADEF Tank Temperature Sensor Plausibility Min Threshold
  • 28B1Foot Throttle Sensor - Signal Below Range Minimum
  • 29Relay First Speed Disconnected
  • 2900Torque Sensor Gap Is On the Larger End Of the Tolerance (CCH Only).
  • 2901Signal Received From the Torque Sensor Is Not In Any Fault Range Or Normal Range Tolerance (CCH Only).
  • 2902Torque Sensor Has Declared An Internal Fault Tolerance (CCH Only).
  • 2903Torque Sensor Supply Voltage Below 4.8 Volts Tolerance (CCH Only).
  • 291012VF1 Voltage Supply Is Low. (Possible Blown Fuse*)
  • 291112VT1 Voltage Supply Is Low. (Possible Blown Fuse*)
  • 291212VF2 Voltage Supply Is Low. (Possible Blown Fuse*)
  • 291312VH Voltage Supply Is Low. (Possible Blown Fuse*)
  • 291412VF3 Voltage Supply Is Low. (Possible Blown Fuse*)
  • 291512VS1 Voltage Supply Is Low. (Possible Blown Fuse*)
  • 291AUpstream SCR Catalyst Temperature Too Low
  • 294ADEF Under Pressure Failure
  • 2999Upstream Oxidation Catalyst Temperature Sensor Voltage is Lower Than Expected
  • 29D3Oil Pressure Sensor Voltage is Lower Than Expected
  • 2A5ADEF Supply Module Pump Motor Pressure Sensor Voltage is Lower Than Expected
  • 2AC4Ambient Temperature Sensor Voltage is Lower Than Expected
  • 2B1AUpstream SCR Catalyst Temperature Sensor Voltage is Lower Than Expected
  • 2B33Fan Speed Below Minimum Threshold
  • 2B36The Minimum Rail Pressure Value Necessary to Allow Fuel Injection Has Not Been Reached
  • 2CD3Oil Temperature Too Low
  • 2D15Fuel Temperature Sensor Voltage is Lower Than Expected
  • 2D54Intake Air Humidity Sensor Voltage is Lower Than Expected
  • 2D93High Pressure Intercooler Outlet Pressure Sensor Plausibility Check Low Failure
  • 2DBEDownstream NOx Sensor Self-Diagnosis Result is Lower Than The Limit
  • 2DDASCR Catalyst Efficiency Lower Than First NOx Production Threshold Level
  • 2E64Intake Manifold Pressure Sensor Voltage is Lower Than Expected
  • 2F3ADEF Tank Temperature Sensor Plausibility Failure
  • 3Logic Box RAM Or Flash EEPROM Error
  • 3000Unknown ECM Error Code Received
  • 3001Foot Throttle Position Sensor - Signal Not Plausible
  • 3002Foot Throttle Sensor - Signal Above Range Maximum
  • 3003Foot Throttle Sensor - Signal Below Range Minimum
  • 3004Foot Throttle Sensor ‐ No Signal ‐ Error
  • 3006Coolant Temperature Signal - Signal Not Plausible (Compared With Engine Oil Temperature)
  • 3007Engine Coolant Temperature Sensor (Downstream) Voltage Is Higher Than Expected
  • 3008Engine Coolant Temperature Sensor Voltage is Lower Than Expected
  • 3009Coolant Temperature Sensor ‐ (via CAN) No Signal
  • 3010Intake Air Pressure And Temperature Sensor - Temperature Signal Too High
  • 3011Intake Air Pressure and Temperature Sensor - Temperature Signal Too Low
  • 3012Air Intake Temperature Sensor ‐ (via CAN) No Signal
Looking for a different Case IH code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Case machine types

Fault code lists by brand