HeavyEquipmentFix
Ask

Case IH Fault Codes List: 3237 to 3333

Page 14 of 30 of the full Case IH fault code list (2,992 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Case IH codes 3237 to 3333

  • 3237Number Of Desired Injections Exceeds Thresholds
  • 3238ECU Power Stages: Errors Of The Power Failure Detection Of CY320
  • 3239Engine Controller EEPROM - Read Operation Failure
  • 3240Engine Controller EEPROM - Write Operation Failure
  • 3241ECU Internal Failure - EEPROM Write or Read Error
  • 3242ECU Internal: Visibility Of Software Resets In DSM
  • 3243Engine Controller Recovery (Suppressed) - Recovery Occurred
  • 3244Engine Controller Recovery (Visible) - Recovery Occurred
  • 3245Turbocharger: Over Boost Deviation At P2 Too High In Pressure Charger Regulator
  • 3246Shutoff Paths During Initialization - Watchdog
  • 3247Shutoff Paths Failed During Initialization - Supply Voltage Too High
  • 3248Shutoff Paths During Initialization - Supply Voltage Too Low
  • 3249TPU Monitoring - Time Deviation Between TPU And System Not Plausible
  • 3250Dataset - Variant Defect
  • 3251Dataset - Requested Variant Could Not Be Set
  • 3252Diagnostic Fault Check To Report Errors In SPI-Communication
  • 3253Analog Digital Converter (ADC) : Diagnostic Fault Check To Report The Error In Voltage Ratio In ADC Monitoring
  • 3254ADC Monitoring - Reference Voltage Too High
  • 3255Analog Digital Converter (ADC) : Diagnostic Fault Check To Report The ADC Test Error
  • 3256Analog Digital Converter (ADC) : Diagnostic Fault Check To Report The NTP Error In ADC Monitoring
  • 3257Turbine Speed And Air Pressure Too High
  • 3258ECU Power Stages: Starter Relay HS Power Stage Output Short Circuit To Battery
  • 3259ECU Power Stages: Starter Relay HS Power Stage Output Short Circuit To Ground
  • 325ADEF Supply Module Pump Temperature is Too Low to Activate Pump
  • 3260Starter Relay - Open Circuit At Low Side Power Stage
  • 3261Starter Relay - Short Circuit To Battery At Low Side Power Stage
  • 3262Starter Relay - Short Circuit To Ground At Low Side Power Stage
  • 3263CAN C Line No Signal
  • 3264Immobilizer ‐ Injection Disabled
  • 3265Diagnostic Fault Check To Report The Error Due To Over Run
  • 3266Redundant Engine Speed In Overrun Monitoring - Speed Signal Not Plausible
  • 3267Main Relay 3 - Short Circuit To Battery
  • 3268Main Relay 3 - Short Circuit To Ground
  • 3269Grid Heater Switch On Test ‐ Voltage Drop Too High
  • 3270Grid Heater Switch On Test ‐ Voltage Drop Too Low
  • 3271Fuel Low Pressure Sensor ‐ (via CAN) No Signal
  • 3272Fuel Low Pressure Sensor ‐ Signal Above Range Max.
  • 3273Fuel Low Pressure Sensor ‐ Signal Below Range Min.
  • 3274Fuel Low Pressure Sensor Dynamic Plausibility Test ‐ Above Map
  • 3275Fuel Low Pressure Sensor Dynamic Plausibility Test ‐ Below Map
  • 3276MIL Visualization Not Available For BC2EDC1
  • 3277Timeout Of CAN Message Dashboard Display
  • 3278ECM Internal Supply Voltage Too High ‐ CJ940 Above Limit
  • 3279ECM Internal Supply Voltage Too Low ‐ CJ940 Below Limit
  • 3280Sensor Supply Voltage 1 - High
  • 3281Sensor Supply Voltage 1 - Low
  • 3282Timeout Of CAN Message WSI (Wheel Speed Info)
  • 3283ECU 5 Volt Sensor Supply 2 Out of Range
  • 3284Sensor Supply Voltage 2 - Low
  • 3285ECU 5 Volt Sensor Supply 3 Out of Range
  • 3286Sensor Supply Voltage 3 - Low
  • 3287Turbo Compound Monitoring ‐ No Signal
  • 3288Turbo Compound Monitoring ‐ Signal High
  • 3289Turbo Compound Monitoring ‐ Signal Low
  • 3290Turbo Compound Monitoring ‐ Signal Not Plausible
  • 3291Cylinder 1 Specific Errors ‐ No Signal
  • 3292Cylinder 1 Specific Errors ‐ Signal Low
  • 3293Fuel Metering Unit: Maximum Positive Deviation Of Rail Pressure Exceeded
  • 3294Cylinder 1 Specific Errors ‐ Signal Not Plausible
  • 3295Cylinder 2 Specific Errors ‐ No Signal
  • 3296Cylinder 2 Specific Errors ‐ Signal Low
  • 3297Cylinder 2 BIP Search Failure ‐ Too Many Unsuccessful Searches ‐ Rail Pressure Positive Deviation High And High Fuel Flow Set Point Value
  • 3298Cylinder 2 Specific Errors ‐ Signal Not Plausible
  • 3299Cylinder 3 Specific Errors ‐ No Signal
  • 329CExhaust Flap Actuator Supply Voltage Out of Range
  • 32BEUpstream NOx Sensor Lambda Signal Deviation - NOx Sensor Possible Removal Detected
  • 3300Cylinder 3 Specific Errors ‐ Signal Low
  • 3301Cylinder 3 BIP Search Failure ‐ Too Many Unsuccessful Searches ‐ Rail Pressure Negative Deviation too High On Minimum Metering
  • 3302Cylinder 3 Specific Errors ‐ Signal Not Plausible
  • 3303Cylinder 4 Specific Errors ‐ No Signal
  • 3304Cylinder 4 Specific Errors ‐ Signal Low
  • 3305Cylinder 4 BIP Search Failure ‐ Too Many Unsuccessful Searches ‐ Rail Pressure Below Minimum Limit in Controlled Mode
  • 3306Cylinder 4 Specific Errors ‐ Signal Not Plausible
  • 3307Cylinder 5 Specific Errors ‐ No Signal
  • 3308Cylinder 5 Specific Errors ‐ Signal Low
  • 3309Cylinder 5 BIP Search Failure ‐ Too Many Unsuccessful Searches ‐ Rail Pressure Above Maximum Limit in Controlled Mode
  • 3310Cylinder 5 Specific Errors ‐ Signal Not Plausible
  • 3311Cylinder 6 Specific Errors ‐ No Signal
  • 3312Compared Camshaft and Crankshaft Speed Sensor Values Are Not Plausible
  • 3313Cylinder 6 BIP Search Failure ‐ Too Many Unsuccessful Searches ‐ Rail Pressure Drop Rate Too High
  • 3314Cylinder 6 Specific Errors ‐ Signal Not Plausible
  • 3315Minimum Number Of Injections Not Reached ‐ Stop Engine
  • 3316Minimum Number Of Injections Not Reached - Stop Engine
  • 3317Minimum Number Of Injections Not Reached ‐ Stop Engine
  • 3318Minimum Number Of Injections Not Reached ‐ Stop Engine
  • 3319DM1DCU SPN2 Message - Error In DCU Active
  • 3320DM1DCU SPN3 Message - Error In DCU Active
  • 3321DM1DCU SPN4 Message - Error In DCU Active
  • 3322DM1DCU SPN5 Message - Error In DCU Active
  • 3323Timeout Of CAN Message RxAMCONIv (Ambient Conditions)
  • 3324Timeout Of CAN Message EBC1 (Electronic Brake Switch)
  • 3325Timeout Of CAN Message ETC1 (Transmission)
  • 3326Timeout Of CAN Message ETC2 (Transmission)
  • 3327Timeout Of CAN Message TCO1 (Tachograph)
  • 3328Timeout Of CAN Message TSC1‐AR (When Inactive)
  • 3329Timeout Of CAN Message TSC1‐AR (When Active)
  • 3330Timeout Of CAN Message TSC1‐DE (When Inactive)
  • 3331Timeout Of CAN Message TSC1‐DE (When Active)
  • 3332Timeout Of CAN Message TSC1‐DR (When Inactive)
  • 3333Timeout Of CAN Message TSC1‐DR (When Active)
Looking for a different Case IH code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Case machine types

Fault code lists by brand