HeavyEquipmentFix
Ask

Case IH Fault Codes List: 17486 to 19

Page 5 of 30 of the full Case IH fault code list (2,992 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Case IH codes 17486 to 19

  • 17486Urea Supply Module: Over Temperature Error On Low Powerstage For Urea Back Flow Pump
  • 17487Urea Supply Module: Short Circuit To Battery Error On Low Powerstage For Urea Back Flow Pump
  • 17488Urea Supply Module: Short Circuit To Ground Error On Low Powerstage For Urea Back Flow Pump
  • 17494Urea Quality Sensor: Short Circuit To Battery (Reported Via CAN Frame ComRx_CRI1)
  • 17495Urea Quality Sensor: Short Circuit To Ground (Reported Via CAN Frame ComRx_CRI1)
  • 17498Urea Quality Sensor: Sensor Internal Fault (Via CAN Frame ComRx_CRI1)
  • 17500Urea Quality Sensor: Short To Battery Of The Temperature Sensor Located In The Urea Quality Sensor (Reported Via CAN Frame ComRx_CRI1)
  • 17501Urea Quality Sensor: Short To Ground Of The Temperature Sensor Located In The Urea Quality Sensor (Reported Via CAN Frame ComRx_CRI1)
  • 17504Urea Quality Sensor: Signal Fault Of The Temperature Sensor Located In The Urea Quality Sensor (Reported Via CAN Frame ComRx_CRI1)
  • 17513PMCat Inlet Temperature Sensor Physical Range Check High
  • 17524Hydrocarbon Level 1 Exceeded
  • 17525EGR Valve: OBD Monitoring Error
  • 17526SCR Inducement: Repeated Offenders Is Active
  • 17527Regeneration Ends Due To Time Exceeded
  • 1758Exhaust Gas Pressure Sensor Voltage is Higher Than Expected
  • 17980Antitampering Checksum Not Received From The Cluster
  • 17981Antitampering Checksum: Checksum Mismatch
  • 17982Antitampering Checksum: Checksum Mismatch (Double Value)
  • 17AADEF Tank Temperature Sensor Plausibility Max Threshold
  • 18CAT2 Flap Closing Switch Short To Ground Or Flap Not Opened
  • 18001Hand Throttle #1 ‐ Voltage Too Low (New Holland Only)
  • 18002Hand Throttle #1 ‐ Voltage Too High (New Holland Only)
  • 18003Hand Throttle Number 2 - Voltage Too Low
  • 18004Hand Throttle Number 2 - Voltage Too High
  • 18005Engine Droop Control - Voltage Too Low
  • 18006Engine Droop Control - Voltage Too High
  • 18007Multi-Function Handle - Switch Error
  • 18008Multi-function Handle - Voltage Too Low
  • 18009Multi-function Handle - Voltage Too High
  • 18010Powershift Throttle ‐ Voltage Too Low (Case IH)
  • 18011Powershift Throttle ‐ Voltage Too High (Case IH)
  • 18012CVT Mode Switch Error
  • 18013Multi-function Handle - Encoder Position Error
  • 18014Rear Hitch Position Control Potentiometer - Voltage Too Low
  • 18015Rear Hitch Position Control Potentiometer - Voltage Too High
  • 18016Rear Hitch Draft Control Potentiometer - Voltage Too Low
  • 18017Rear Hitch Draft Control Potentiometer - Voltage Too High
  • 18018Rear Hitch Height Limit Potentiometer - Voltage Too Low
  • 18019Rear Hitch Height Limit Potentiometer - Voltage Too High
  • 18020Rear Hitch Drop Rate Potentiometer - Voltage Too Low
  • 18021Rear Hitch Drop Rate Potentiometer - Voltage Too High
  • 18022Rear Hitch Sensitivity Control Potentiometer - Voltage Too Low
  • 18023Rear Hitch Sensitivity Control Potentiometer - Voltage Too High
  • 18024EHR Flow Encoder Position Error
  • 18025Rear Hitch Slip Control Potentiometer - Voltage Too Low
  • 18026Rear Hitch Slip Control Potentiometer - Voltage Too High
  • 18027EHR 5 Lever Position ‐ Voltage Too Low (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of the ACM)
  • 18028EHR 5 Lever Position ‐ Voltage Too High (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18029EHR 6 Lever Position ‐ Voltage Too Low (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18030EHR 6 Lever Position ‐ Voltage Too High (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18031Front Hitch Position / Pressure Control Potentiometer ‐ Voltage Too High
  • 18032Front Hitch Position / Pressure Control Potentiometer ‐ Voltage Too Low
  • 18033Front Hitch Position / Pressure Mix Potentiometer ‐ Voltage Too High
  • 18034Front Hitch Position / Pressure Mix Potentiometer ‐ Voltage Too Low
  • 18035Front Hitch Position Height Limit Potentiometer ‐ Voltage Too High
  • 18036Front Hitch Position Height Limit Potentiometer ‐ Voltage Too Low
  • 18037Front Hitch Height Limit Enable Switch Error
  • 18038Front Hitch Position Drop Rate Potentiometer ‐ Voltage Too High
  • 18039Front Hitch Position Drop Rate Potentiometer ‐ Voltage Too Low
  • 18040EHR (Remote Valve) 1 Lever Position - Voltage Too Low
  • 18041EHR (Remote Valve) 1 Lever Position - Voltage Too High
  • 18042EHR (Remote Valve) 2 Lever Position - Voltage Too Low
  • 18043EHR (Remote Valve) 2 Lever Position - Voltage Too High
  • 18044EHR (Remote Valve) 3 Lever Position - Voltage Too Low
  • 18045EHR (Remote Valve) 3 Lever Position - Voltage Too High
  • 18046EHR (Remote Valve) Float Control Switch Error
  • 18047EHR (Remote Valve) 4 Lever Position - Voltage Too Low
  • 18048EHR (Remote Valve) 4 Lever Position - Voltage Too High
  • 18049Joystick 1 X-Axis Position - Voltage Too Low
  • 18050Joystick 1 X-Axis Position - Voltage Too High
  • 18051Joystick 1 Y-Axis Position - Voltage Too Low
  • 18052Joystick 1 Y-Axis Position - Voltage Too High
  • 18053Joystick 1 Proportional Rocker Switch - Voltage Too Low
  • 18054Joystick 1 Proportional Rocker Switch ‐ Voltage Too High
  • 18055Joystick 2 X‐Axis Position ‐ Voltage Too Low (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18056Joystick 2 X‐Axis Position ‐ Voltage Too High (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18057Joystick 2 Y‐Axis Position ‐ Voltage Too Low (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18058Joystick 2 Y‐Axis Position ‐ Voltage Too High (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18059Joystick 2 Proportional Rocker Switch ‐ Voltage Too Low (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18060Joystick 2 Proportional Rocker Switch ‐ Voltage Too High (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18061Reference Voltage - Short Circuit To Ground
  • 18062Reference Voltage - Short Circuit To 12V
  • 18063EEEPROM Error
  • 18064Multi-Function Handle Communication Error
  • 18065Multi-Function Handle Basic Assurance Test Error
  • 18066EHR (Remote Valve) 1 Lever Implausibility Error
  • 18067EHR (Remote Valve) 2 Lever Implausibility Error
  • 18068EHR (Remote Valve) 3 Lever Implausibility Error
  • 18069EHR (Remote Valve) 4 Lever Implausibility Error
  • 18070EHR 5 Lever Implausibility Error (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18071EHR 6 Lever Implausibility Error (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18072EDC Mouse Raise/Work Switch Fault (NH Only)
  • 18181Reverting Valve (4‐2way Valve?) Electrically – 'Short Circuit To Battery – 'P20A3 Vent Valve (Reductant Purge Control Valve) ‐ Short Circuit High
  • 181AUpstream SCR Catalyst Temperature Too High
  • 184AMonitoring of Over Pressure
  • 1865Fuel Rail Pressure Has Exceeded Maximum Limit
  • 1899Upstream Oxidation Catalyst Temperature Sensor Voltage is Higher Than Expected
  • 18D3Oil Pressure Sensor Voltage is Higher Than Expected
  • 18DENH3 Sensor Short in Heater Circuit Causing Overheating
  • 19CAT4 Actuator Potentiometer Short To Ground
Looking for a different Case IH code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Case machine types

Fault code lists by brand