HeavyEquipmentFix
Ask

Deutz Fahr Fault Codes List: 1484 to 2315

Page 4 of 11 of the full Deutz Fahr fault code list (1,004 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Deutz Fahr codes 1484 to 2315

  • 1484Master ECU and Slave ECU Have Been Identified as the Same Types
  • 1485Master ECU and Slave ECU Data Sets or Software are Not Identical
  • 1486SCR Main Relay; Open Load (Only CV56B)
  • 1487SCR Main Relay; Power Stage Over Temperature (Only CV56B)
  • 1488SCR Main Relay; Short Circuit to Battery (Only CV56B)
  • 1489SCR Main Relay; Short Circuit to Ground (Only CV56B)
  • 1490SCR Reversing Valve; Open Load
  • 1491SCR Reversing Valve; Over Temperature
  • 1493SCR Reversing Valve; Short Circuit to Ground
  • 1494Physical Range Check High for EGR Mass Flow
  • 1495Physical Range Check Low for EGR Mass Flow
  • 1496Exhaust Gas Recirculation; EGR Mass Flow; Shut Off Demand
  • 14S1DPF System; Operating Voltage Error
  • 14S2CAN Message ComMS_Sys7 Not Received From Slave
  • 14S3Metering Control is Not Performed in Time Error
  • 1505Electric Fuel Pump; Fuel Pressure Build Up Error
  • 1523Exhaust Gas Recirculation AGS Sensor; Plausibility Error
  • 1524Physical Range Check High for EGR Exhaust Gas Mass Flow
  • 1525Physical Range Check Low for EGR Exhaust Gas Mass Flow
  • 1526Exhaust Gas Recirculation; AGS Sensor has "Burn Off" Not Performed
  • 1527AGS Sensor Temperature Exhaust Gas Mass Flow; Plausibility Error
  • 1615Maximum Stand - Still - Duration Reached; Oil Exchange Required
  • 1616DPF Differential Pressure Sensor and a Further Sensor or Actuator CRT System Defective
  • 1617Temperature Sensor US. and DS. DOC Simultaneously Defect
  • 1659Time Out Error of CAN - Transmit - Frame A1DOC
  • 1660Time Out Error of CAN - Transmit - Frame AT1S
  • 1661Time Out Error of CAN - Transmit - Frame SCR2
  • 1662Time Out Error of CAN - Transmit - Frame SCR3
  • 1663Time Out Error of CAN - Transmit - Frame DPFBrnAirPmpCtl
  • 1664Time Out Error of CAN - Transmit - Frame ComDPFBrnPT
  • 1665Time Out Error of CAN - Transmit - Frame ComDPFCl
  • 1666Time Out Error of CAN - Transmit - Frame ComDPFHisDat
  • 1667Time Out Error of CAN - Transmit - Frame ComDPFTstMon
  • 1668Time Out Error of CAN - Transmit - Frame ComEGRMsFlw
  • 1669Time Out Error of CAN - TComEGRTVActr
  • 1670Time Out Error of CAN - Transmit - Frame ComETVActr
  • 1671Time Out Error of CAN - Transit - Frame ComlTVActr
  • 1672Time Out Error of CAN - Receive - Frame ComRxCMl
  • 1673Time Out Error of CAN - Receive - Frame ComRxCustSCR3
  • 1674Time Out Error of CAN - Receive - Frame ComRxDPFBrnAirPmpCtl
  • 1675Time Out Error of CAN - Receive - Frame ComRxDPFBrnAirPmp
  • 1676Time Out Error of CAN - Receive - Frame ComRxDPFCtl
  • 1677Time Out Error of CAN - Receive - Frame ComRxEGRMsFlwl
  • 1678Time Out Error of CAN - Receive - Frame ComRxEGRMsFlw2
  • 1679Time Out Error of CAN - Receive - Frame ComRxEGRTVActr
  • 168Time Out Error of CAN - Transmit - Frame EEC3VOL1; Engine Send Messages
  • 1680Time Out Error of CAN - Receive - Frame ComRxETVActr
  • 1681Time Out Error of CAN - Receive - Frame ComRxlTVActr
  • 1682Time Out Error of CAN - Receive - Frame ComRxSCRHtDiag
  • 1683Time Out Error of CAN - Receive - Frame ComRxTrbChActr
  • 1684Time Out Error of CAN - Receive - Frame ComRxUQSens
  • 1685Time Out Error of CAN - Receive - Frame ComSCRHtCtl
  • 1686Time Out Error of CAN - Receive - Frame ComTxATllMG
  • 1687Time Out Error of CAN - Receive - Frame ComTxTrbChActr
  • 169Time Out Error of CAN - Transmit - Frame EEC3VOL2; Engine Send Messages
  • 171Time Out Error of CAN - Receive - Frame ComEngPrt; Engine Protection
  • 179Time Out CAN - Message FunModCtl; Function Mode Control
  • 198Time Out Error of CAN - Receive - Frame PrHtEnCmd; Pre-Heat Command, Engine Command
  • 2Air Flow Sensor Load Correction Factor Exceeding Drift Limit; Plausibility Error
  • 202Time Out Error of CAN - Receive - Frame UAA10; AGS Sensor Service Message
  • 203Time Out Error of CAN - Receive - Frame UAA11; AGS Sensor Data
  • 211Power Up - Power cycle
  • 2110Power Up - Joystick S4 Button Active at Power Up
  • 2111Power Up - Engine Start Prevented - Platform Start Switch High at Power Up
  • 2112Power Up - Platform Rotate Left Prevented - Input High at Power Up
  • 2113Power Up - Platform Rotate Right Prevented - Input High at Power Up
  • 2114Power Up - Platform Level Up Prevented - Input High at Power Up
  • 2115Power Up - Platform Level Down Prevented - Input High at Power Up
  • 2116Power Up - APU Switch Input Invalid - Input High at Power Up
  • 2117Power Up - Platform Joystick Not in Neutral Position at Power Up
  • 2118Power Up - Engine Pre-Heat Prevented - Input High at Power Up
  • 2119Power Up - Frame Level Right Input - Invalid Signal
  • 212Time Out Error of CAN - Receive - Frame RxEngPres; Status Burner Air Pump
  • 2120Power Up - Frame Level Left Input - Invalid Signal
  • 2121Power Up - Hydraulic Quick Connect Input - Invalid Signal
  • 2122Power Up - Continuous Auxiliary Hydraulics Switch High at Power Up
  • 2123Power Up - Joystick Trigger Switch Active at Power Up
  • 2124Power Up - Joystick Left Roller Not in the Neutral Position at Power Up
  • 2125Power Up - Joystick Right Roller Not in the Neutral Position at Power Up
  • 2130Power Up - Boom Ride Enable Switch Not in the Off Position at Power Up
  • 214Power Up - Function Enable Inputs - Invalid Signal States
  • 215Power Up - Joystick Axes Not in Neutral Position at Power Up
  • 216Power Up - Joystick Roller Not in Neutral Position at Power Up
  • 217Power Up - Joystick S1 Button Active at Power Up
  • 218Power Up - Joystick S2 Button Active at Power Up
  • 219Power Up - Joystick S3 Button Active at Power Up
  • 2225Platform Controls - Platform Level - Conflicting Input Signals
  • 2226Platform Controls - Platform Rotate - Conflicting Input Signals
  • 2227Platform Controls - Function Enable Interlock - Enable Switch Not Selected First
  • 2228Platform Controls - Function Enable Interlock - Not Selected in Time
  • 2229Platform Controls - Engine Start Prevented - Function Enable Switch Engaged
  • 2230Platform Controls - Platform Joystick - Out of Range High
  • 2231Platform Controls - Platform Joystick - Center Tap Bad
  • 2233Platform Controls - Function Enable Relay - Invalid Signal
  • 2311Ground Controls - Platform Option Not Configured
  • 23119Seat Switch Disagreement
  • 2312Ground Controls - Stabilizers Not Configured
  • 2313Ground Controls - Frame Level Not Configured
  • 2314Ground Controls - Operating Station Selection Invalid
  • 2315Ground Controls - Operating Mode Interlock - Stabilizers Not Deployed
Looking for a different Deutz Fahr code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Deutz machine types

Fault code lists by brand