HeavyEquipmentFix
Ask

Deutz Fault Codes List: 876 to P0073

Page 13 of 17 of the full Deutz fault code list (1,684 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Deutz codes 876 to P0073

  • 876Maximum rail pressure exceeded (PRV).
  • 877Sensor error rail pressure. Sensor voltage above upper limit.
  • 878Sensor error rail pressure. Sensor voltage below lower limit.
  • 88Charged air pressure above warning threshold.
  • 881Long-term adaption factor below threshold.
  • 882NOx conversion rate insufficient (SCR-Cat defect, bad quality).
  • 883NOx conversion rate insufficient (SCR-Cat defect, bad quality); temperature range 1
  • 887DFC For Plausibility Error Min For NOx Sensor Downstream of SCR Cat
  • 889DFC For Plausibility Error Max For NOX Sensor Upstream Of SCR Cat
  • 89Charged air pressure above shut off threshold
  • 892Sensor backflow line pressure (SCR); plausibility error.
  • 893SCR Monitoring; Pressure stabilization error, general pressure check error (SCR).
  • 894Pressure stabilization error dosing valve (SCR).
  • 897Pump pressure SCR metering unit too high.
  • 898Pump pressure SCR metering unit too low.
  • 899Pressure overload of SCR-System.
  • 9Air inlet filter temperature, plausibility error.
  • 90Parameter Fault (EEPROM Retrieval or Checksum Faulty)
  • 900Pressure build-up error SCR-System.
  • 903DEF tank temperature too high.
  • 905Sensor SCR catalyst upstream temperature too high; plausibility error
  • 908DEF dosing valve blocked (SCR).
  • 91Low Fuel Pressure: Erratic, Intermittent Or Incorrect
  • 914DEF supply module heater temperature; plausibility error (normal condition).
  • 915Sensor DEF Supply Module Heater Temperature; Plausibility Error (Cold Start Condition)
  • 916Sensor DEF supply module temperature; plausibility error (cold start condition).
  • 917SCR plausibility, OBD and diagnosis; Stuck in range check DEF tank temperature sensor. DEF-tank without heating function (heating phase)
  • 918SCR Plausibility, OBD and Diagnosis; Stuck In Range Check Of DEF Tank Temperature Sensor DEF-Tank Without Heating Function (Heating Phase)
  • 919DFC to block the fuel by Sia, No detail information!
  • 92Physical range check high for coolant temperature.
  • 920DFC to indicate that TEN-code or UC-code received if ECU is learned. No detail information!
  • 921DFC to indicate that TEN-code or UC-code received if ECU is learned. No detail information!
  • 922DFC To Indicate That No KWP Code Is Received Via CAN. No Details Available
  • 923DFC To Indicate That Wrong KWP Code Is Received. No Details Available
  • 925Urea Supply Module Heater Temperature; Duty Cycle in Failure Range
  • 926DEF supply module heater temperature; duty cycle in invalid range.
  • 927Urea supply module temperature measurement not available.
  • 928DEF supply module PWM signal; period outside valid range.
  • 929Defeat faulty PWM signal from Supply Modul.
  • 93Physical range check low for coolant temperature.
  • 930Def supply module temperature; duty cycle in failure range.
  • 931Urea supply module temperature; duty cycle in invalid range.
  • 932Hand throttle idle validation switch; short circuit to battery.
  • 935Sensor Error Accelerator Pedal. Signal Voltage High (Possible Open Circuit)
  • 937Hand throttle Idle Validation Switch; Short Circuit to Ground
  • 94CAN Message DecV1 (Pseudo Pedal): Erratic, Intermittent Or Incorrect
  • 940Sensor error accelerator pedal. Signal is below the range.
  • 942Sensor Error Burner Temperature; Signal Voltage High (Possible Open Circuit)
  • 943Sensor Error DEF Tank Level; Signal Voltage High (Possible Open Circuit)
  • 944Sensor Error Burner Temperature; Signal Voltage Low (Possible Short Circuit)
  • 945Sensor Error DEF Tank Level; Signal Voltage Low (Possible Short Circuit)
  • 946Failure of sensor supply voltage 1.
  • 947Failure of sensor supply voltage 2.
  • 948Failure of sensor supply voltage 3
  • 95CAN Message FunModCtl (Function Mode Control): Errormode Not Identifiable
  • 956Starter relay high side. Short circuit to battery.
  • 957Starter relay high side short circuit to ground.
  • 958Starter Relay Low Side Open Circuit Error
  • 959Starter relay powerstage over temperature.
  • 96Sensor Error Coolant Temperature; Signal Voltage High (Possible Open Circuit)
  • 960Starter relay low side short circuit to batter.
  • 961Starter relay low side short circuit to ground.
  • 965Burner shut of valve; short circuit to battery.
  • 969SVS Lamp; Open Circuit
  • 97Sensor Error Coolant Temperature; Signal Voltage Low (Possible Short Circuit)
  • 970SVS lamp; powerstage over temperature.
  • 971SVS lamp; short circuit to battery.
  • 972SVS lamp; short circuit to ground.
  • 973Software reset CPU SWReset_0
  • 974Software reset CPU SWReset_1
  • 975Software reset CPU SWReset_2
  • 976Sensor Voltages Do Not Agree; APP1 and APP2 Or APP1 And Idle Switch
  • 978Plausibility error between sensor and idle switch, Accelerator Pedal Detection. In case of Hand Throttle with Low Idle Switch, it is the plausibility check between hand throttle and idle switch.
  • 98High coolant temperature; Warning threshold exceeded.
  • 980Terminal 50 (Ignition Start Input) Was Operated Too Long
  • 981Air flow temperature sensor; short circuit to battery or operator load.
  • 982Air flow temperature sensor; short circuit to ground.
  • 986Burner temperature, temperature above upper shutoff threshold.
  • 989Burner temperature, temperature below lower shutoff threshold.
  • 99Coolant Temperature High; System Reaction Initiated
  • 992Charged Air cooler down stream temperature. Temperature below lower physical threshold.
  • 994Electrical error charged air temperature. Signal range check high (SRC).
  • 995Boost Temperature Sensor; Signal Voltage Low (Possible Short Circuit)
  • 996Charged air cooler temperature. System reaction initiates High charged air cooler temperature. Warning threshold exceeded.
  • 997Charged Air Cooler Temperature; High Charged Air Cooler Temperature. Shut Off Threshold Exceeded
  • 998Diagnostic fault check for charged air cooler downstream temperature sensor. No detail information!
  • A050Basic control unit in emergency mode
  • A051Restricted engine function due to CAN bus/EDC programming
  • A053Air conditioning control ECU not working
  • B014Collecting shaft sensor speeds do not match
  • B015Bevel pinion sensor possible faults detected
  • B016Travel range detection potentiometer change detected
  • B020Hall speed sensor button issue detected
  • B021PTO speed sensor issue detected
  • B039High-pressure sensor fault detected
  • B077Engine fan speed sensor circuit error
  • B088Crankshaft speed sensor value exceeded
  • B089Temperature sensor fault
  • P0072Ambient air temp sensor voltage below normal or short to ground
  • P0073Ambient air temp sensor voltage above normal or short to power
Looking for a different Deutz code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Deutz machine types

Fault code lists by brand