HeavyEquipmentFix
Ask

Deutz Fault Codes List: 562 to 693

Page 11 of 17 of the full Deutz fault code list (1,684 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Deutz codes 562 to 693

  • 562Check Of Missing Injector Adjustment Value Programming (IQA) Injector 4 (In Firing Order)
  • 563Check Of Missing Injector Adjustment Value Programming (IQA) Injector 5 (In Firing Order)
  • 564Check Of Missing Injector Adjustment Value Programming (IQA) Injector 6 (In Firing Order)
  • 565Injector Cylinder - Bank 1; Short Circuit
  • 566Injector Cylinder - Bank 2; Short Circuit
  • 567Injector powerstage output defect.
  • 568Injector 1 (in firing order): Interruption of electric connection.
  • 569Injector 2 (in firing order): Interruption of electric connection.
  • 57Burner Control: Power reduction due to low lambda. Engine Power: Not enough oxygen for regeneration.
  • 570Injector 3 (in firing order): Interruption of electric connection.
  • 5706DEF pump heating valve critical high output current
  • 571Injector 4 (in firing order): Interruption of electric connection.
  • 572Injector 5 (in firing order): Interruption of electric connection.
  • 573Injector 6 (in firing order): Interruption of electric connection.
  • 575Special pattern for special cases, No detail information!
  • 576Special pattern for special cases, No detail information!
  • 577Special pattern for special cases, No detail information!
  • 5771EGR valve - Hardware error
  • 578Special pattern for special cases, No detail information!
  • 579Special pattern for special cases, No detail information!
  • 5796SCR system (air pump/air supply valve) - Out of service
  • 58Burner dosing valve (DV2); Overcurrent at the end of the injection phase.
  • 580Injector 1 (in firing order): Short circuit.
  • 581Injector 2 (in firing order): Short circuit.
  • 582Injector 3 (in firing order): Short circuit.
  • 5826Power or speed reduction due to SCR failure
  • 5829EGR valve - No sensor position data available
  • 583Injector 4 (in firing order): Short circuit.
  • 584Injector 5 (in firing order): Short circuit.
  • 585Injector 6 (in firing order): Short circuit.
  • 59Burner dosing valve (DV2); Powerstage over temperature.
  • 590High side to low side short circuit in the injector 5 (in firing order).
  • 591High side to low side short circuit in the injector 6 (in firing order).
  • 592Metering Unit (Fuel System); Open Circuit
  • 593Metering unit (Fuel-System): Powerstage over temperature.
  • 594Metering Unit (Fuel System); Power Short Circuit To Battery High Side
  • 595Metering unit (Fuel-System): Short circuit to ground, high side.
  • 596Metering Unit (Fuel-System); Short Circuit to Battery Low Side
  • 597Metering Unit (Fuel-System); Short Circuit To Ground Low Side
  • 598Metering unit, short circuit to battery.
  • 599Metering unit, short circuit to ground.
  • 6Set Point 2 Hand Throttle Circuit
  • 60Burner dosing valve (DV2); Short circuit to battery.
  • 604Too many recognized misfires in cylinder 1 (in firing order)
  • 605Too many recognized misfires in cylinder 2 (in firing order).
  • 606Too many recognized misfires in cylinder 3 (in firing order)
  • 607Too many recognized misfires in cylinder 4 (in firing order).
  • 608Too many recognized misfires in cylinder 5 (in firing order).
  • 609Too many recognized misfires in cylinder 6 (in firing order)
  • 61Reserve Output 2: Errormode Not Identifiable
  • 610No Detail Available
  • 611Misfire detection monitoring, No detail information!
  • 612Internal ECU monitoring detection reported error.
  • 613ECU reported internal software error. Internal ECU monitoring detection reported error.
  • 614ECU reported internal software error
  • 615ECU reported internal software error.
  • 616ECU reported internal software error.
  • 617ECU reported internal software error.
  • 618ECU reported internal software error.
  • 619Injection system, electrical error injectors.
  • 62Burner dosing valve (DV2); Short circuit to ground.
  • 620ECU reported internal software error.
  • 621ECU reported internal software error.
  • 623ECU reported internal software error.
  • 624ECU reported internal software error.
  • 625ECU reported internal software error.
  • 627ECU reported internal software error.
  • 628ECU reported internal software error.
  • 629Diagnostic fault check to report the accelerator pedal position error.
  • 63Burner dosing valve (DV2); Short circuit high side powerstage.
  • 630Diagnostic fault check to report the engine speed error.
  • 631Error in the plausibility of the injection energizing time.
  • 632Error in the plausibility of the start of energizing angles.
  • 633Diagnostic fault check to report the error due to non plausibility in ZFC.
  • 634Diagnosis fault check to report the demand for normal mode due to an error in the Pol2 quantity.
  • 635Diagnosis fault check to report the error to demand for an ICO due to an error in the Pol2 shut-off.
  • 636Diagnosis fault check to report the error to demand for an ICO due to an error in the Pol3 efficiency factor.
  • 637Internal ECU monitoring detection reported error.
  • 638Monitoring of Fuel Quantity Correction.
  • 639Diagnostic fault check to report the plausibility error in rail pressure monitoring.
  • 64Burner dosing valve (DV2); downstream pressure sensor plausibility error.
  • 640Diagnostic fault check to report the error due to torque comparison.
  • 641Diagnosis of curr path limitation forced by ECU monitoring level 2.
  • 642Diagnosis of curr path limitation forced by ECU monitoring level 2.
  • 643Diagnosis of curr path limitation forced by ECU monitoring level 2.
  • 644Reported Over Voltage of Supply.
  • 646Reported Under Voltage of Supply.
  • 647Fan 1 short circuit to battery (high side)
  • 648Manipulation control was triggered.
  • 649Timeout error in Manipulation control.
  • 654Early opening defect of main relay, No detail information!
  • 656DFC for stuck main relay error, No detail information!
  • 659NOx feed back fault detection, No detail information!
  • 66Physical range check high for burner dosing valve (DV2) downstream pressure; Shut off regeneration.
  • 67Error Hand Setp1
  • 677Starter locked due to overtemperature
  • 68CAN Setpoint 1 Error
  • 69Physical range check low for burner dosing valve (DV2) downstream pressure; Shut off regeneration. When burner injector is actuated, the measured pressure does not rise above 1250mbar abs (expected: about 2400mbar).
  • 692Plausibility error during Rich to Lean switch over, No detail information!
  • 693Monitoring of NOx signal readiness, No detail information!
Looking for a different Deutz code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Deutz machine types

Fault code lists by brand