HeavyEquipmentFix
Ask

Deutz Fault Codes List: 259 to 4206

Page 7 of 17 of the full Deutz fault code list (1,684 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

Deutz codes 259 to 4206

  • 259CAN Message OilVlv5 (Valve 5): Error Not Identifiable
  • 26When AirHt_ctDefSRCLoOn_mp is lower than AirHt_ctMaxDef_C. DFC to SRC Low error when heater is on.
  • 260CAN Message STIN1 (State Inputs 1): Errormode Not Identifiable
  • 261CAN Message Step (State Electrical Fuel Supply Pump: Errormode Not Identifiable
  • 262CAN Message StLmp (State Lamp): Errormode Not Identifiable
  • 2623Accelerator pedal sensor 2 voltage short circuit or open circuit
  • 263CAN Message StOut (State Outputs): Errormode Not Identifiable
  • 2630Intercooler downstream temp sensor supply voltage out of range
  • 27Beginning Of Injection Of Cylinder 4: Erratic, Intermittent Or Incorrect
  • 273DFC SAE J1939 error.
  • 2791EGR valve - Communication error detected by control module
  • 28Healing takes place if the condition for error detection is present. Air temperature monitoring plausibility check array.
  • 2809Air filter 2 is blocked or clogged.
  • 281Timeout Error Of CAN- Receive - Frame Active TSV1AE
  • 282Timeout error of CAN-Receive-Frame Passive TSC1AE.
  • 283Timeout error of CAN-Receive-Frame Active TSC1AR.
  • 284Timeout error of CAN-Receive-Frame Passive TSC1AR.
  • 29Beginning Of Injection Of Cylinder 6: Erratic, Intermittent Or Incorrect
  • 291Timeout Error Of CAN - Receive - Frame TSX1TE- Active
  • 292Passive timeout error of CAN-Receive-Frame TSC1TE. Setpoint.
  • 293Timeout error of CAN-Receive-Frame TSC1TR.
  • 294Passive timeout error of CAN-Receive-Frame TSC1TR.
  • 299Timeout error of CAN-Transmit-Frame TrbCH. Status Wastegate.
  • 3Speed Sensor
  • 30Healing takes place if the condition for error detection is present. Air temperature monitoring plausibility check array.
  • 300Timeout error of CAN-Receive-Frame TSC1AE. Traction Control.
  • 301Timeout error of CAN-Receive-Frame TSC1AR. Retarder.
  • 3031DEF tank temperature sensor value out of maximum range
  • 305Timeout error of CAN-Receive-Frame TSC1TE. Setpoint.
  • 306Timeout Error Of CAN-Receiver-Frame TSC1TR; Control Signal
  • 31Beginning Of Injection Of Cylinder 8: Erratic, Intermittent Or Incorrect
  • 313Timeout error of CAN-Transmit-Frame UAA11
  • 32Charge Air Pressure Sensor: Erratic, Intermittent Or Incorrect
  • 322Timeout error of CAN-Transmit-Frame UAA1 on CAN 2. Control burner air pump.
  • 3222NOx sensor upstream SCR - Heater performance error
  • 3224NOx sensor upstream SCR - Communication error
  • 3225NOx sensor upstream SCR removed from exhaust line
  • 3232NOx sensor downstream SCR - Heater performance error
  • 3234NOx sensor downstream SCR - Communication error
  • 3235NOx sensor downstream SCR removed from exhaust line
  • 3251DPF differential pressure sensor - Short circuit to ground or open circuit
  • 3253Particulate filter DPF pressure drop high limit
  • 3264NOx sensor upstream SCR 2 - Heater performance error
  • 3273NOx sensor downstream SCR 2 - Heater performance error
  • 33Charge Air Pressure: Erratic, Intermittent Or Incorrect
  • 3340Intercharger downstream pressure sensor plausibility error
  • 3360Aftertreatment control module communication error
  • 3363DEF tank heating valve critical high output current
  • 3364DEF tank quality sensor value out of maximum range
  • 3382Alternator short circuit to battery (high side)
  • 34Coolant Level Warning
  • 35Speed Warning (With Thrust Mode Operation)
  • 3511ECU sensor supply voltage 3 error cause unknown
  • 3512ECU sensor supply voltage 4 exact fault cause unknown
  • 3513Sensor supply voltage 5, cause unknown
  • 3514Sensor supply voltage 6, cause unknown
  • 3515DEF tank temperature sensor at suction position value out of maximum range
  • 3516DEF tank - Poor AdBlue quality
  • 3532AdBlue tank level low error
  • 354Air filter combi sensor ambient humidity error
  • 3562Intake manifold pressure sensor 2 plausibility error
  • 3585Ignition on while emergency stop is active
  • 36Fuel Temperature Warning
  • 360Power Stage Diagnosis Disabled, High Battery Voltage
  • 361Powerstage diagnosis disabled. Low battery voltage.
  • 362Engine brake Pre-Selection switch. Plausibility error.
  • 37Short Circuit to battery error of actuator relay 2.
  • 3711DPF regeneration stopped (temperature too low)
  • 3719Particulate filter DPF - High Soot Load warning
  • 3720Air filter differential pressure sensor voltage below normal or short to ground
  • 3750DPF regeneration stopped (temperature too high)
  • 376Access error EEPROM memory (delete).
  • 377Access error EEPROM memory (read).
  • 378Access error EEPROM memory (write).
  • 38UB3: Short Circuit to Battery Error of Actuator Relay 3
  • 381Physical range check low for EGR differential pressure.
  • 384Actuator EGR valve. Powerstage over temperature.
  • 387Internal software error ECU. Injection cut off.
  • 388Engine speed above warning threshold. Overspeed detection in component engine protection.
  • 389Engine Speed Above Warning Threshold (FOC - Level 1)
  • 39Misfire At Cylinder 2: Errormode Not Identifiable
  • 390Engine speed above warning threshold (FOC-Level 2).
  • 391Engine speed above warning threshold (Overrun Mode).
  • 4Excess Speed Switch Off
  • 40UB5; Short Circuit to Battery Error of Actuator Relay 5 (UB6) SCR-Heater/Rev. Valve
  • 4076Coolant temperature sensor 2 plausibility error
  • 4090SCR efficiency monitor high error on NOx emission
  • 41Short circuit to ground error. Detail information not available.
  • 411Ambient Air Pressure Received From A CAN-Bus Is Reported As Defective
  • 412Sensor Error Ambient Air Pressure, Signal Voltage High (Possible Open Circuit)
  • 413Sensor Error Ambient Air Pressure, Signal Voltage Low (Possible Short Circuit)
  • 415Environment Temperature Sensor, Temperature Above Upper Physical Threshold
  • 416Environment temperature physical range check low.
  • 417Sensor error SCR-System environment temperature. DPF-System air inlet temperature, signal range check high.
  • 418Sensor error SCR-System environment temperature. DPF-System air inlet temperature, signal range check low.
  • 419Sensor Camshaft Speed, Disturbance Signal
  • 42Short Circuit to ground error of actuator relay 2.
  • 420Sensor Camshaft Speed, Detection, Out Of Range, Signal Disrupted, No Signal
  • 4201Air flap control speed over error.
  • 4206CAN frame transmission torque speed control counter error
Looking for a different Deutz code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other Deutz machine types

Fault code lists by brand