Deutz Fault Codes List: 516571 to 561
Page 10 of 17 of the full Deutz fault code list (1,684 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.
Deutz codes 516571 to 561
- 516571SCR system - DEF not defrosted after legal time elapsed
- 516572Multiselector switch supply voltage out of range
- 516577High pressure pump 1 installation error
- 516655SCR system 3 very low conversion efficiency
- 516656SCR system 4 very low conversion efficiency
- 516657SCR system 5 - Very low conversion efficiency
- 516662NOx sensor downstream SCR 3 - Heater performance error
- 516663NOx sensor downstream SCR 4 - Heater performance error
- 516664NOx sensor downstream SCR 5 - Heater performance error
- 516671Critical activation overtime in low idle speed adjustment release button
- 516672Critical activation overtime in PTO On button
- 516673Critical activation overtime in PTO Off button
- 516674Critical activation overtime in positive speed adjustment button
- 516675Critical activation overtime in negative speed adjustment button
- 516676Critical activation overtime in cruise control button 3
- 516678EATS temperature sensors position inversion error
- 516709Fuel cut off due to insufficient oil pressure before start
- 516710Fuel cut off due to insufficient oil level before start
- 516736Oil pressure at inlet engine filter underpressure warning
- 516737Start request before CAN is ready (Starter 1)
- 516738Start request before CAN is ready (Starter 2)
- 516739Starter inhibition due to emergency stop activation
- 516747ECU power supply - Critical overcurrent
- 516756SCR efficiency monitor high error on NOx emission
- 516759NOx sensor upstream SCR 2 - Invalid sensor status
- 516761DPF - Driver regeneration maintained too long (security threshold)
- 516762SCR system - Dosing deviation error
- 516763SCR system 2 - Dosing deviation error
- 516764SCR system 3 - Dosing deviation error
- 516765SCR system 4 - Dosing deviation error
- 516766SCR system 5 - Dosing deviation error
- 516791Starter plausibility coordinator ECU internal safety error
- 516792Starter plausibility command ECU internal safety error
- 516795SCR system temperature too high
- 516796Starter ECU output current maximum plausibility error
- 516797Starter ECU output temperature too high
- 516812Volume control valve current plausibility error
- 516816Short circuit to battery in neutral switches for regeneration
- 516817Engine position detection error (engine status)
- 516818Engine position detection error (transition to running)
- 516819Speed sensors phase angle difference too high
- 516820Signal edge detection error in camshaft position
- 516821Teeth sequence detection error in camshaft position
- 516822Teeth recognition error in camshaft position
- 516823Expected teeth not detected in camshaft position
- 516824Teeth without gap in crankshaft position
- 516825Tooth miss error in crankshaft position
- 516827Signal edge not in acceptance window in crankshaft position
- 516828Crankshaft position sensor power supply signal short circuit to battery
- 516829Crankshaft position sensor ground signal short circuit to battery
- 516830Crankshaft position sensor value out of range
- 516831Crankshaft position sensor defect
- 516832Camshaft position sensor power supply signal short circuit to battery
- 516833Camshaft position sensor ground signal short circuit to battery
- 516834Camshaft position sensor value out of range
- 516835Camshaft position sensor defect
- 516836Crankshaft position 2 plausibility error
- 516838Injection release ECU internal safety error
- 516839ECU injection driver not correctly initialized
- 516855Body Controller communication error.
- 517024CAN frame transmission output shaft speed counter error
- 517025CAN output shaft speed checksum error.
- 517051System ECU failure during demand.
- 518231CAN frame transmission counter error
- 518232CAN frame transmission checksum error.
- 52Engine Brake Actuator (Internal): Errormode Not Identifiable
- 520306DEF pump motor overtemperature fault
- 520308DEF return line heater overtemperature, cause unknown
- 520309DEF pressure line heater overtemperature, cause unknown
- 520310DEF suction line heating relay overtemperature fault
- 520312DEF tank heating valve overtemperature fault
- 520319DEF tank temperature fault
- 520425Cold start device faulty component
- 520471DEF downstream line heater, cause unknown
- 524Sensor Error DV1 & DV2 Upstream Pressure; Signal Voltage High (Possible Open Circuit)
- 525Sensor Error DV1 & DV2 Upstream Pressure; Signal Voltage Low (Possible Short Circuit)
- 53Indicator Lamp Of Air Heater Relay: Erratic, Intermittent Or Incorrect
- 5319DPF regeneration failed
- 534Main/Shut-Off Valve Temperature; Signal Voltage High (Possible Open Circuit)
- 535Main/Shut-Off Valve Temperature; Signal Voltage Low (Possible Short Circuit)
- 5386Wastegate valve - Short circuit to battery (high side)
- 54Warning Lamp For Coolant Temperature: Errormode Not Identifiable
- 542Hydraulic oil temperature check for Shut off condition.
- 543Cold Start Device Relay Error
- 5435SCR system DEF pump short circuit to battery
- 544Cold Start Aid Relay Open Circuit
- 545Cold start aid relay open load.
- 547Cold start aid relay: Over temperature error.
- 5484Fan 2 short circuit to battery (high side)
- 5485SCR system (DEF pump) - Out of service
- 549Intake Air Heater Device: Short circuit to battery.
- 55Air pump doesn't achieve air mass flow setpoint. Burner Control - burner air pump.
- 551Air Intake Heater, Short Circuit To Ground Error For Power Stage On CJ945
- 5536Hydraulic oil temp sensor - Short circuit to battery
- 5543Exhaust flap - Communication error detected by control module
- 5571Pressure control valve short circuit to battery
- 559Check Of Missing Injector Adjustment Value Programming (IQA) Injector 1 (In Firing Order)
- 56Burner Control. Burner does not start after several trials (burner flame to detection). Burner flame unintentional deleted.
- 560Check Of Missing Injector Adjustment Value Programming (IQA) Injector 2 (In Firing Order)
- 561Check Of Missing Injector Adjustment Value Programming (IQA) Injector 3 (In Firing Order)
Other Deutz machine types
Fault code lists by brand
- CAT8,286 codes
- Volvo6,508 codes
- New Holland Tractor3,475 codes
- FPT3,033 codes
- Case IH2,992 codes
- Bobcat2,653 codes
- Challenger Tractor2,434 codes
- New Holland Combine2,274 codes
- John Deere Tractors1,884 codes
- Case Wheel Loader1,859 codes
- John Deere Engines1,853 codes
- Cummins1,847 codes
- Challenger Rubber Track Tractor1,747 codes
- Volvo Wheel Loader1,726 codes
Safety-critical: confirm before use
Safety first: park on level ground, stop the engine, and secure the machine before any inspection. Thresholds, component locations, wire numbers, fuse locations, and reset procedures can vary by model, configuration, and serial number. Confirm them in the service documentation for your exact machine.