HeavyEquipmentFix
Ask

FPT Fault Codes List: 17501 to 18D3-1F

Page 5 of 31 of the full FPT fault code list (3,033 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

FPT codes 17501 to 18D3-1F

  • 17501Urea Quality Sensor: Short To Ground Of The Temperature Sensor Located In The Urea Quality Sensor (Reported Via CAN Frame ComRx_CRI1)
  • 17504Urea Quality Sensor: Signal Fault Of The Temperature Sensor Located In The Urea Quality Sensor (Reported Via CAN Frame ComRx_CRI1)
  • 17513PMCat Inlet Temperature Sensor Physical Range Check High
  • 17524Hydrocarbon Level 1 Exceeded
  • 17525EGR Valve: OBD Monitoring Error
  • 17526SCR Inducement: Repeated Offenders Is Active
  • 17527Regeneration Ends Due To Time Exceeded
  • 1758Exhaust Gas Pressure Sensor Voltage is Higher Than Expected
  • 17980Antitampering Checksum Not Received From The Cluster
  • 17981Antitampering Checksum: Checksum Mismatch
  • 17982Antitampering Checksum: Checksum Mismatch (Double Value)
  • 17AADEF Tank Temperature Sensor Plausibility Max Threshold
  • 17CECU Internal - Internal Reset - Clock Loss - Voltage Too Low
  • 18Electrical Failures of Sensors - Sensor Supply 2 (5V Internal; for Urea Level Sensor)
  • 18001Hand Throttle #1 ‐ Voltage Too Low (New Holland Only)
  • 18002Hand Throttle #1 ‐ Voltage Too High (New Holland Only)
  • 18003Hand Throttle #2 ‐ Voltage Too Low
  • 18004Hand Throttle #2 ‐ Voltage Too High
  • 18005Engine Droop Control ‐ Voltage Too Low
  • 18006Engine Droop Control ‐ Voltage Too High
  • 18007Multi‐Function Handle ‐ Switch Error
  • 18008Multi‐Function Handle ‐ Voltage Too Low
  • 18009Multi‐Function Handle ‐ Voltage Too High
  • 18010Powershift Throttle ‐ Voltage Too Low (Case IH)
  • 18011Powershift Throttle ‐ Voltage Too High (Case IH)
  • 18012CVT Mode Switch Error
  • 18013Multi‐Function Handle ‐ Encoder Position Error
  • 18014Rear Hitch Position Control Potentiometer ‐ Voltage Too Low
  • 18015Rear Hitch Position Control Potentiometer ‐ Voltage Too High
  • 18016Rear Hitch Draft Control Potentiometer ‐ Voltage Too Low
  • 18017Rear Hitch Draft Control Potentiometer ‐ Voltage Too High
  • 18018Rear Hitch Height Limit Potentiometer ‐ Voltage Too Low
  • 18019Rear Hitch Height Limit Potentiometer ‐ Voltage Too High
  • 18020Rear Hitch Drop Rate Potentiometer ‐ Voltage Too Low
  • 18021Rear Hitch Drop Rate Potentiometer ‐ Voltage Too High
  • 18022Rear Hitch Sensitivity Control Potentiometer ‐ Voltage Too Low
  • 18023Rear Hitch Sensitivity Control Potentiometer ‐ Voltage Too High
  • 18024EHR Flow Encoder Position Error
  • 18025Rear Hitch Slip Control Potentiometer ‐ Voltage Too Low
  • 18026Rear Hitch Slip Control Potentiometer ‐ Voltage Too High
  • 18027EHR 5 Lever Position ‐ Voltage Too Low (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of the ACM)
  • 18028EHR 5 Lever Position ‐ Voltage Too High (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18029EHR 6 Lever Position ‐ Voltage Too Low (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18030EHR 6 Lever Position ‐ Voltage Too High (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18031Front Hitch Position / Pressure Control Potentiometer ‐ Voltage Too High
  • 18032Front Hitch Position / Pressure Control Potentiometer ‐ Voltage Too Low
  • 18033Front Hitch Position / Pressure Mix Potentiometer ‐ Voltage Too High
  • 18034Front Hitch Position / Pressure Mix Potentiometer ‐ Voltage Too Low
  • 18035Front Hitch Position Height Limit Potentiometer ‐ Voltage Too High
  • 18036Front Hitch Position Height Limit Potentiometer ‐ Voltage Too Low
  • 18037Front Hitch Height Limit Enable Switch Error
  • 18038Front Hitch Position Drop Rate Potentiometer ‐ Voltage Too High
  • 18039Front Hitch Position Drop Rate Potentiometer ‐ Voltage Too Low
  • 18040EHR 1 Lever Position ‐ Voltage Too Low
  • 18041EHR 1 Lever Position ‐ Voltage Too High
  • 18042EHR 2 Lever Position ‐ Voltage Too Low
  • 18043EHR 2 Lever Position ‐ Voltage Too High
  • 18044EHR 3 Lever Position ‐ Voltage Too Low
  • 18045EHR 3 Lever Position ‐ Voltage Too High
  • 18046EHR Float Control Switch Error
  • 18047EHR 4 Lever Position ‐ Voltage Too Low
  • 18048EHR 4 Lever Position ‐ Voltage Too High
  • 18049Joystick 1 X‐Axis Position ‐ Voltage Too Low
  • 18050Joystick 1 X‐Axis Position ‐ Voltage Too High
  • 18051Joystick 1 Y‐Axis Position ‐ Voltage Too Low
  • 18052Joystick 1 Y‐Axis Position ‐ Voltage Too High
  • 18053Joystick 1 Proportional Rocker Switch ‐ Voltage Too Low
  • 18054Joystick 1 Proportional Rocker Switch ‐ Voltage Too High
  • 18055Joystick 2 X‐Axis Position ‐ Voltage Too Low (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18056Joystick 2 X‐Axis Position ‐ Voltage Too High (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18057Joystick 2 Y‐Axis Position ‐ Voltage Too Low (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18058Joystick 2 Y‐Axis Position ‐ Voltage Too High (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18059Joystick 2 Proportional Rocker Switch ‐ Voltage Too Low (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18060Joystick 2 Proportional Rocker Switch ‐ Voltage Too High (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18061Reference Voltage – Short Circuit To 0V
  • 18062Reference Voltage – Short Circuit To 12V
  • 18063EEPROM Fault
  • 18064MFH Communication Error
  • 18065MFH Basic Assurance Test Error
  • 18066EHR 1 Lever Implausibility Error
  • 18067EHR 2 Lever Implausibility Error
  • 18068EHR 3 Lever Implausibility Error
  • 18069EHR 4 Lever Implausibility Error
  • 18070EHR 5 Lever Implausibility Error (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18071EHR 6 Lever Implausibility Error (Not Applicable To CCM/APH – It May Indicate Incorrect Configuration Of The ACM)
  • 18072EDC Mouse Raise/Work Switch Fault (NH Only)
  • 18181Reverting Valve (4‐2way Valve?) Electrically – 'Short Circuit To Battery – 'P20A3 Vent Valve (Reductant Purge Control Valve) ‐ Short Circuit High
  • 181AUpstream SCR Catalyst Temperature Too High
  • 184AMonitoring of Over Pressure
  • 184A-0SCR Reagent Feeding
  • 184A-1FSCR Reagent Feeding
  • 1865Fuel Rail Pressure Has Exceeded Maximum Limit
  • 1865-0Fuel Pressure Control Metering Unit
  • 1865-1FFuel Pressure Control Metering Unit
  • 1899Upstream Oxidation Catalyst Temperature Sensor Voltage is Higher Than Expected
  • 1899-0Oxicat Temp Sensing
  • 1899-1FOxicat Temp Sensing
  • 18D3Oil Pressure Sensor Voltage is Higher Than Expected
  • 18D3-0Oil Pressure Sensing
  • 18D3-1FOil Pressure Sensing
Looking for a different FPT code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Fault code lists by brand