HeavyEquipmentFix
Ask

FPT Fault Codes List: 19289 to 19872

Page 7 of 31 of the full FPT fault code list (3,033 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

FPT codes 19289 to 19872

  • 19289Temperature After Catalyst Too Low – 'Downstream Catalyst Temp ‐ Physical (Catalyst Heating Time Failed) – 'P042B Catalyst Temperature Sensor Circuit Range/Performance
  • 19298UREA Pressure Too Low At System Start – 'UREA Pressure Too Low At System Start – 'P208B Reagent Pump Not Delivering
  • 19307UREA Pressure Too High – 'Urea Pressure Not Plausible (Urea Pressure Too High) – 'P204B Reagent ‐ Pressure Above Threshold
  • 19316UREA Temperature In Pump Module Out Of Range – 'Urea Temperature Box ‐ Physical (Urea Box Temp NOT OK: Outside Range) – 'P2043 Reagent‐Temperature Sensor Of Pump Module Out Of Range
  • 19323External Engine Shutdown Request Received
  • 19325UREA Temperature In Tank Out Of Range – 'Urea Temperature Tank ‐ Physical (Urea Tank Temp NOT OK: Outside Range) – 'P205B Reagent ‐ Tank Temperature Sensor (Temperature Of The Reagent ‐ Solution In The Tank) Out Of Range
  • 19334System Frozen And Not Free In Time – Defreezing Mode And Detection Errors (Inlet Line Defreezing Failed) – P20C2 Reagent ‐ Suction Tube Heating ‐ Detection Mode Of Heating
  • 19335System Frozen And Not Free In Time – 'Defreezing Mode And Detection Errors (Pressure Line Defreezing Failed) – 'P20BE Reagent ‐ Pressure Tube Heating ‐ Detection Mode Of Heating
  • 19336System Frozen And Not Free In Time – 'Defreezing Mode And Detection Errors (Pressure Build‐Up In Detection Mode Failed) – 'P20C5 Pump Module ‐ Internal Heating ‐ Open Circuit
  • 19337System Frozen And Not Free In Time – 'Defreezing Mode And Detection Errors (Back‐Flow Line Defreezing Failed) – 'P20B9 Reagent ‐ Backflow Tube Heating ‐ Open Circuit
  • 19343Coolant Control Valve Mechanically – 'Mechanical Defective Blocked Open – 'P20A3 Vent Valve (Reductant Purge Control Valve) ‐ Short Circuit High
  • 19344Coolant Control Valve Mechanically – Mechanical Defective Blocked Closed – P20A0 Vent Valve (Reductant Purge Control Valve) ‐ Open Circuit
  • 19345Timeout Error Of CAN Receive Frame HCU Data
  • 19346Timeout Error Of CAN Receive Frame HCU Data
  • 19352Reverting Valve (4‐2way Valve?) Mechanically – 'Valve Does Not Open – 'P20A0 Vent Valve (Reductant Purge Control Valve) ‐ Open Circuit
  • 19356Downstream NOx Sensor Signal And NH3 Sensor Signal Plausibility Check Failure
  • 19361Battery Voltage (Actual Value) – 'High Battery Voltage – 'P0562 Battery Voltage Evaluation ‐ Below Lower Limit
  • 19362Battery Voltage (Actual Value) – Low Battery Voltage – P0563 Battery Voltage Evaluation ‐ Above Upper Limit
  • 19364Tank Heating Valve – 'Open Load – 'P20B1 Reagent ‐ Tank Heating Valve ‐ Open Circuit
  • 19370UREA Pressure Too Low (In "Commissioning" Status) – 'Pump Motor Error During Commissioning (Pump Not Delivering) – 'P208B Reagent‐Pump Not Delivering
  • 19379UREA Temperature Too Low During Commissioning – 'Temperatures Not Plausible During Commissioning.
  • 19402CAN Timeout Error - Urea Tank Level
  • 19415Empty UREA Tank – Urea Tank Empty – P203F Reagent ‐ Fluid Level In Tank ‐ Too Low
  • 19421Downstream NOx Sensor Failed Negative Drift Test Monitoring
  • 19422Downstream NOx Sensor Signal Is Stuck At A Constant Value
  • 19423Upstream NOx Sensor Comparison To A Calculated NOx Value Failure
  • 19434ECU Internal Failure - EEPROM Erase Error
  • 19435ECU Internal Failure - EEPROM Read Error
  • 19436ECU Internal Failure - EEPROM Write Error
  • 19496Monitoring Of Over Pressure
  • 19505DEF/AdBlue Supply Module Temperature Sensor Cold Start Plausibility Failure
  • 19523DEF/AdBlue Tank Temperature Failure
  • 19532Back Flow Line Clogged – 'P2063 Reagent ‐ Dosing Valve ‐ Short Circuit Low
  • 19541Coolant Control Valve Mechanically – 'Blocked Closed – 'P20A1 Vent Valve Test Plausibility Test (Startup)
  • 19550Pressure Line Blocked – 'Pressure Line Blocked – 'P209B Reagent ‐ Dosing Nozzle ‐ Pressure Too High
  • 19559Low UREA Level 1 (Warning) ‐ UREA Level Below Limit 1 ‐ P203F Reagent ‐ Fluid Level In Tank ‐ Too Low
  • 19568Low UREA Level 2 (Warning) ‐ UREA Level Below Limit 2 ‐ P203F Reagent ‐ Fluid Level In Tank ‐ Too Low
  • 19577CAN Receive Frame E2SCR (Dosing, Exh Gas Flow, Exh Gas Temp, Error Suppression, Heater, Long Term Failure) – 'SAE J1939 Check For CAN Receive Signal : (UREA Quantity Not In Range) – 'P0600
  • 19578CAN Receive Frame E2SCR (Dosing, Exh Gas Flow, Exh Gas Temp, Error Suppression, Heater, Long Term Failure) – 'SAE J1939 Check For CAN Receive Signal : (Dosing Status Not In Range) – 'P0600 Serial Communication Link
  • 19579CAN Receive Frame E2SCR (Dosing, Exh Gas Flow, Exh Gas Temp, Error Suppression, Heater, Long Term Failure) – Timeout – P0600 Serial Communication Link
  • 19580CAN Receive Frame E2SCR (Dosing, Exh Gas Flow, Exh Gas Temp, Error Suppression, Heater, Long Term Failure) – 'Too Many CAN Messages – 'P0600 Serial Communication Link
  • 19581CAN Receive Frame E2SCR (Dosing, Exh Gas Flow, Exh Gas Temp, Error Suppression, Heater, Long Term Failure) – SAE J1939 Check For CAN Receive Signal – P0600 Serial Communication Link
  • 19595CAN Receive Frame EEC1 (Driver Demand, Eng Speed, Eng Torque) – 'SAE J1939 Check For CAN Receive Signal : (Engine Torque Not In Range) – 'P0600 Serial Communication Link
  • 19596CAN Receive Frame EEC1 (Driver Demand, Eng Speed, Eng Torque) – 'SAE J1939 Check For CAN Receive Signal : (Engine Speed Not In Range) – 'P0600 Serial Communication Link
  • 19597CAN Receive Frame EEC1 (Driver Demand, Eng Speed, Eng Torque) – Timeout – P0600 Serial Communication Link
  • 19598CAN Receive Frame EEC1 (Driver Demand, Eng Speed, Eng Torque) – 'Too Many CAN Messages – 'P0600 Serial Communication Link
  • 19599CAN Receive Frame EEC1 (Driver Demand, Eng Speed, Eng Torque) – 'SAE J1939 Check For CAN Receive Signal : (Torque Driver Demand Not In Range) – 'P0600 Serial Communication Link
  • 195ADEF Supply Module Pump Motor Pressure Sensor Voltage is Higher Than Expected
  • 195A-0SCR Reagent Pressure Sensor
  • 195A-1FSCR Reagent Pressure Sensor
  • 19604CAN Receive Frame ET1 (Oil And Water Temp Engine) – 'SAE J1939 Check For CAN Receive Signal : (Oil Temperature Not In Range) – 'P0600 Serial Communication Link
  • 19605CAN Receive Frame ET1 (Oil And Water Temp Engine) – Timeout – P0600 Serial Communication Link
  • 19606CAN Receive Frame ET1 (Oil And Water Temp Engine) – 'Too Many CAN Messages – 'P0600 Serial Communication Link
  • 19607CAN Receive Frame ET1 (Oil And Water Temp Engine) – 'SAE J1939 Check For CAN Receive Signal : (Water Temperature Not In Range) – 'P0600 Serial Communication Link
  • 19649UREA Tank Level Error (CAN Message Or Electrical With Real Sensor) – 'Level Over CAN: SAE J1939 No Signal Available Level Sensor Connected Directly: Sensor Supply Error – 'P203A Reagent ‐ Tank Level Sensor ‐ Open Circuit
  • 19650UREA Tank Level Error (CAN Message Or Electrical With Real Sensor) – Level Over CAN: SAE J1939 Signal Not In Range Level Sensor Connected Directly: SRC High – P203D Reagent ‐Tank Level Sensor ‐ Short Circuit High
  • 19651UREA Tank Level Error (CAN Message Or Electrical With Real Sensor) – 'Level Over CAN: SAE J1939 Erroneous Signal Level Sensor Connected Directly: SRC Low – 'P203C Reagent ‐ Tank Level Sensor ‐ Short Circuit Low
  • 19666Quantity Balance Check If A Successful PRV Opening Is Ensured
  • 19676Ambient Temperature: SAE J1939 Check For CAN Receive Signal : (Signal Range Check: Signal Not In Range / Erroneous Signal / Signal Not Available) – 'SAE J1939 Check For CAN Receive Signal : (Ambient Air Temperature Not In Range) – 'P0600 Serial Communication Link
  • 19677Ambient Temperature: SAE J1939 Check For CAN Receive Signal : (Signal Range Check: Signal Not In Range / Erroneous Signal / Signal Not Available) – Timeout – P0071 Ambient Air Temperature Sensor Range/Performance
  • 19678Ambient Temperature: SAE J1939 Check For CAN Receive Signal : (Signal Range Check: Signal Not In Range / Erroneous Signal / Signal Not Available) – 'Too Many CAN Messages – 'P0071 Ambient Air Temperature Sensor Range/Performance
  • 19679Ambient Temperature: SAE J1939 Check For CAN Receive Signal : (Signal Range Check: Signal Not In Range / Erroneous Signal / Signal Not Available) – 'SAE J1939 Check For CAN Receive Signal : (Barometric Pressure Not In Range) – 'P0071 Ambient Air Temperature Sensor Range/Performance
  • 19721EEPROM / Checksum Failures – 'EEPROM Write Error – 'P062F Internal Control Module EEPROM Error
  • 19722EEPROM / Checksum Failures – 'No Corresponding Variant Number Error – 'P062F Internal Control Module EEPROM Error
  • 19723EEPROM / Checksum Failures – 'EEPROM Communication Error – 'P062F Internal Control Module EEPROM Error
  • 19724EEPROM / Checksum Failures – EEPROM Detection Error OR 'Codierwort Error – 'P062F Internal Control Module EEPROM Error
  • 19725EEPROM / Checksum Failures – 'Wrong EEPROM Size – 'P062F Internal Control Module EEPROM Error
  • 19730Ignition "On" Signal K15 – 'Digital Input Ignition ON Not Sensed During Initialization – 'P2530 Ignition Switch ‐ Plausibility Error
  • 19739Main Relay Opens Too Early / Too Late – 'Main Relay Shut Off Too Late – 'P0687 ECM/PCM Power Relay Control Circuit High
  • 19740Main Relay Opens Too Early / Too Late – 'Main Relay Short Circuit – 'P0685 ECM/PCM Power Relay Control Circuit /Open
  • 19741Main Relay Opens Too Early / Too Late – 'Main Relay Open Circuit – 'P0687 ECM/PCM Power Relay Control Circuit High
  • 19742Main Relay Opens Too Early / Too Late – Main Relay Shut Off Too Early (Before EEPROM Update) – P0685 ECM/PCM Power Relay Control Circuit /Open
  • 19748Too High Urea Temperature In Pump Module Or Leakage Test Failed (Emergency Shut Off) – Over Temperature Detection (Urea Temp. In Pump Module) – P2043 Reagent ‐Temperature Sensor Of Pump Module ‐ Out Of Range
  • 19749Too High UREA Temperature In Pump Module Or Leakage Test Failed (Emergency Shut Off) – 'Urea Leakage Detection (Static Or Dynamic) – 'P202D Dynamic Urea Leakage Test ‐ Leakage Detected
  • 19757Group Error Path UREA Injection Control – Error Belonging To Group UREA Injection Control – P208B Reagent‐Pump ‐ Not Delivering
  • 19766Group Error Path Air Control – Error Belonging To Group Air Control – P20A7 Compressed Air Regulation Valve
  • 19775Group Error Path Catalyst Temperature – Error Belonging To Group Catalyst Temperature Out Of Range – P0426 Plausibility Of Catalyst Temperature Sensors ‐Plausibility Error (Static)
  • 19784Group Error Path Nox Exceeded – Error Belonging To Group Nox Exceeded Active – P2000 Nox Trap Efficiency Below Threshold
  • 19787SCR Inducement: Level 1 (Torque Reduction), Triggered By DEF/AdBlue Dosing Interruption Fault
  • 19788SCR Inducement: Level 3 (Creep Mode), Triggered By DEF/AdBlue Dosing Interruption Fault
  • 19789SCR Inducement: Warning, Triggered By DEF/AdBlue Dosing Interruption Fault
  • 19793Group Error Path UREA Tank Empty – Error Belonging To Group UREA Tank Empty Active – P203F Reagent ‐ Fluid Level In Tank ‐ Too Low
  • 19797SCR Inducement: Level 1 (Torque Reduction), Triggered By DEF/AdBlue Quality Fault
  • 19798SCR Inducement: Level 3 (Creep Mode), Triggered By DEF/AdBlue Quality Fault
  • 19799SCR Inducement: Warning, Triggered By DEF/AdBlue Quality Fault
  • 19800SCR Inducement: Level 1 (Torque Reduction), Triggered By Tampering Fault
  • 19801SCR Inducement: Level 3 (Creep Mode), Triggered By Tampering Fault
  • 19809SCR Inducement Control: Diagnosis Validation Is Active
  • 19817DEF/AdBlue Dosing Valve Is Blocked
  • 19835Open Load Temperature Error On The Turbocharger PWM Output Powerstage
  • 19836Over Temperature Error On The Turbocharger PWM Output Powerstage
  • 19837SCB Error On The Turbocharger PWM Output Powerstage
  • 19838SCG Error On The Turbocharger PWM Output Powerstage
  • 19858SRC High For Turbine Upstream Temperature Sensor
  • 19859SRC Low For Turbine Upstream Temperature Sensor
  • 19862Power Stage Error In HCU For DEF/AdBlue Back Flow Line Heater
  • 19865Short Circuit To Battery Of DEF/AdBlue Backflow Line Heater Actuator Powerstage
  • 19866Short Circuit To Ground Of DEF/AdBlue Backflow Line Heater Actuator Powerstage
  • 19870Short Circuit To Ground Of DEF/AdBlue Pressure Line Heater Actuator Powerstage
  • 19872Power Stage Error In HCU For DEF/AdBlue Supply Module Heater
Looking for a different FPT code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Fault code lists by brand