New Holland Tractor Fault Codes List: 14202 to 15249
Page 6 of 35 of the full New Holland Tractor fault code list (3,475 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.
New Holland Tractor codes 14202 to 15249
- 14202Short Circuit to Ground on the Signal Coming from the Steering Sensor
- 14203Short Circuit to +12 V or Open Circuit on the Supply Signal to the Electro-Hydraulic 4WD Engagement/Release Relay Coil
- 14204Short Circuit to Ground on the Supply Signal to the Electrohydraulic 4WD Engagement/Release Relay Coil
- 1425Fuel Rail Pressure Sensor Voltage is Higher Than Expected
- 143Front Suspension Position is Above the Upper Suspension Range
- 14300Electronic Park Lock (EPL) - Mismatch Between CAN and Direct Frequency Input Info
- 14301Electronic Park Lock (EPL) - Direct Frequency Input Shorted to VCC or Open Circuit
- 14304Electronic Park Lock (EPL) - Status Not Validated
- 1438Turbocharger Boost Pressure is Higher Than Expected
- 144Compared Camshaft and Crankshaft Speed Sensor Values Are Not Plausible
- 144EDEF Quality Sensor Internal Failure (Concentration Value is Higher Than Expected)
- 145Front Suspension Lower Lock Solenoid Circuit Shorted or Open Circuit
- 146Hydraulic Pump Failed, System Pressure Low
- 147Out of Range Error High on the #1 Feedback
- 148Out of Range Error Low on the #1 Feedback
- 149Out of Range Error High on the #2 Feedback
- 14900Transmission Controller Missing (RB/RD/RF/RG)
- 14901Engine Controller Missing (EDC16)
- 14902Auxiliary Controller Missing (RC/RH/RK/Rl)
- 14904Armrest Control Module (ACM) Missing (LC)
- 14905Keypad Missing (JA)(ADIC Only)
- 14906Fast Steering Control Module (FSCM) Missing (KA)
- 14907Gear Display Missing
- 14908Tractor Electronic Control Unit (TECU) Missing (OA)
- 14909SWCD Missing (VA)
- 14910Automatic Temperature Control (ATC) Module Missing
- 14911Enhanced Cluster Detected without Keypad
- 14912Basic Cluster with Keypad
- 149134WD Control Module Missing
- 14914Electronic Park Lock (EPL) Controller Missing (XA)
- 14915MV Missing
- 14920Configuration Error
- 14921Hardware ID Not Programmed
- 14922Incorrect Steering Sensor Configuration
- 15The Harness of the External Switches of the Rising and Lowering Electrohydraulic Remote Valves Short Circuit, Open Circuit or in Fault
- 150Out of Range Error Low on the #2 Feedback
- 15002Steering Wheel Control Proximity Sensor - Open Circuit
- 15003Steering Wheel Control Proximity Sensor - Short Circuit
- 15006Split Valve LVDT - Open Circuit
- 15007Split Valve LVDT - Short Circuit
- 15008Change Valve Solenoid - Open Circuit
- 15009Change Valve Solenoid - Short Circuit Across
- 15010Safety Switch Fail
- 15011Maximum Engagement Time Elapsed (5 Minutes)
- 15012Split Valve Spool - Stuck Open
- 15013Change Valve or Split Valve Spools - Stuck Closed
- 15014Split Valve Spool Stuck in Transition Zone - Can't Identify Which Steering Mode the Tractor is Definitely in
- 15024System Not Calibrated
- 151Fuel Rail Pressure Has Exceeded Maximum Positive Deviation Limits
- 152EHR Top Link Switch Short
- 15200Steering Valve Controller Battery - Voltage Too High
- 15201Steering Valve Controller Battery - Voltage Too Low
- 15202Steering Valve Controller Failure - Software Flash Test Failure
- 15203Steering Valve Controller Failure - Software RAM Code Test Failed
- 15204Steering Valve Controller Failure - Software PSM Task Failure
- 15205Steering Valve Controller Failure - Software Program Sequence Monitoring Failure
- 15206Steering Valve Controller Has Detected the CAN Bus Offline
- 15207Steering Valve Controller Has Detected a Duplicate Source Address
- 15208Steering Valve Controller Failure - Software Interpolation Overflow or Underflow or Incorrect Data
- 15209Steering Valve Controller Failure - Software I2C Communication Failure
- 15210Steering Valve Controller Failure - Software Variable Truncation
- 15211Steering Valve Controller Failure - Software Division by Zero
- 15212Steering Valve Controller Failure - Software Initialization Failure
- 15213Steering Valve Controller Failure - Coil Supply Switch State Synchronization Between Main and Safety Controllers Failed
- 15214Steering Valve Controller Failure - Coil Supply Switch State is Incorrect For Operation
- 15215Steering Valve Controller Failure - Coil Supply Switch Self-Test Failed
- 15216Steering Valve Controller Failure - EEPROM Write Failed
- 15217Primary Wheel/Articulation Angle Sensor Check with Redundant Wheel Angle Sensor Failed
- 15218Primary Wheel/Articulation Angle Sensor - Voltage Too Low
- 15219Primary Wheel/Articulation Angle Sensor - Voltage Too High
- 15220Redundant Wheel/Articulation Angle Sensor - Voltage Too Low
- 15221Redundant Wheel/Articulation Angle Sensor - Voltage Too High
- 15222Steering Valve Controller - Average Temperature Too High
- 15223Steering Valve Controller - Temperature Too High
- 15224Steering Valve Controller - Temperature Too Low
- 15225Steering Valve Controller - 5 Volt Supply Too High
- 15226Steering Valve Controller - 5 Volt Supply Too Low
- 15227Auto Guidance Cut-Off Solenoid Supply - Voltage Too Low
- 15228Auto Guidance Cut-Off Solenoid Supply - Voltage Too High
- 15229Auto Guidance Cut-Off Solenoid Supply - Duty Cycle Differs From Expected Value
- 15230Auto Guidance Cut-Off Solenoid Supply - High Resistance or Open Circuit
- 15231Auto Guidance Cut-Off Solenoid Supply - Low Resistance or Short to Ground
- 15232Steering Wheel Sensor - Communication Data Error
- 15233Steering Wheel Sensor - Communication Lost
- 15234Steering Wheel Sensor - Offline
- 15235Steering Wheel Sensor - Invalid Velocity or Position Value
- 15236Vehicle Speed Sensor - Message (From UCM) Communication Data Error
- 15237Vehicle Speed Sensor - Message (From UCM) Communication Lost
- 15238Vehicle Speed Sensor Message (From UCM) Offline
- 15239Vehicle Speed Sensor - Message (From UCM) Invalid Speed Value
- 15240Steering Control - Message (From UCM) Communication Data Error
- 15241Steering Control - Message (From UCM) Communication Lost
- 15242Steering Control - Message (From UCM) Offline
- 15243Steering Control - Message (From UCM) Invalid Data Value
- 15244Incorrect Steering Valve Controller Configuration - Auxiliary Steering Device Enabled
- 15245Incorrect Steering Valve Controller Configuration - Auxiliary Steering Device Enabled
- 15246Incorrect Steering Valve Controller Configuration - Auxiliary Steering Device Enabled
- 15247Incorrect Steering Valve Controller Configuration - Auxiliary Steering Device Enabled
- 15248Vehicle Speed Too High
- 15249Steering Valve Spool Out of Neutral at Power-Up
Other New Holland machine types
Fault code lists by brand
- CAT8,286 codes
- Volvo6,508 codes
- FPT3,033 codes
- Case IH2,992 codes
- Bobcat2,653 codes
- Challenger Tractor2,434 codes
- John Deere Tractors1,884 codes
- Case Wheel Loader1,859 codes
- John Deere Engines1,853 codes
- Cummins1,847 codes
- Challenger Rubber Track Tractor1,747 codes
- Volvo Wheel Loader1,726 codes
- Deutz1,684 codes
- Perkins1,523 codes
Safety-critical: confirm before use
Safety first: park on level ground, stop the engine, and secure the machine before any inspection. Thresholds, component locations, wire numbers, fuse locations, and reset procedures can vary by model, configuration, and serial number. Confirm them in the service documentation for your exact machine.