HeavyEquipmentFix
Ask

FPT Fault Codes List: 3096 to 319E-0

Page 13 of 31 of the full FPT fault code list (3,033 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

FPT codes 3096 to 319E-0

  • 3096Tier 3: ECM Bus Off on CAN A Tier 4a: ECM Bus Off On Vehicle CAN
  • 3097ECM Bus Off On Engine Private CAN
  • 3098Timeout Of CAN Message TSC1‐TE (When Active)
  • 3099Timeout Of CAN Message TSC1‐TE (When Inactive)
  • 3100Timeout Of CAN Message TSC1‐AE (When Active)
  • 3101Timeout Of CAN Message TSC1‐AE (When Inactive)
  • 3102Fuel Rail Pressure Sensor Voltage is Lower Than Expected
  • 3104Fuel Pressure Relief Valve is Open
  • 3105Fuel Pressure Relief Valve is Forced to Open, Perform Pressure Increase
  • 3106Fuel Pressure Relief Valve Reached Maximum Allowed Opening Count
  • 3107Fuel Metering Unit is Shorted to Battery Voltage at The Low Side
  • 3108Fuel Metering Unit is Shorted to Ground at The Low Side
  • 3110Rail Pressure Sensor Offset Monitoring ‐ Value Above Limit
  • 3111Rail Pressure Sensor Offset Monitoring ‐ Value Below Limit
  • 3112Fuel Rail Pressure Sensor Voltage is Higher Than Expected
  • 3113Main Relay 1 (High Pressure Pump ‐ Power Supply To the Fuel Metering Unit) ‐ Short To Battery
  • 3114Main Relay 1 (High Pressure Pump ‐ Power Supply To the Fuel Metering unit) Short To Ground
  • 3117PTO Twist Sensor ‐ Out Of Range
  • 3118ECM 12V Sensor Supply Voltage High
  • 3119ECM 12V Sensor Supply Voltage Low
  • 3120PTO Twist Sensor ‐ Not Plausible
  • 3121PTO Twist Sensor ‐ Open Circuit
  • 3122PTO Twist Sensor – Short Circuit To Ground
  • 3123PTO Twist Sensor ‐ Not Calibrated
  • 3124Hand Throttle ‐ Channel 2 Above Range Max.
  • 3125Hand Throttle ‐ Channel 2 Below Range Min.
  • 3126Hand Throttle ‐ Channel 1 Signal Above Range Max.
  • 3127Hand Throttle ‐ Channel 1 Signal Below Range Min.
  • 3128Hand Throttle ‐ Channel Difference Error
  • 3129Hand Throttle ‐ Idle Switch Closed Circuit
  • 3130Hand Throttle ‐ Idle Switch Open Circuit
  • 3131Grid Heater Always Switched On
  • 3133Cold Start Lamp ‐ No Load
  • 3134Cold Start Lamp – Short circuit to Battery
  • 3135Cold Start Lamp – Short Circuit To Ground
  • 3136Cold Start Lamp ‐ Excessive Temperature
  • 3137Fuel Metering Unit Has an Open Load Error
  • 3138Metering Unit ‐ Temperature Too High
  • 3139Metering Unit Signal Range Check - Signal Too High
  • 3140Metering Unit Signal Range Check - Signal Too Low
  • 3141Fuel Flow Setpoint Too Low - Fuel Metering Unit: Leakage Is Detected Based On Fuel Quantity Balance
  • 3142High Pressure Test ‐ Test Active
  • 3143Grid Heater Switch Off Test (Voltage Drop Too High)
  • 3144Grid Heater Switch Off Test (Voltage Drop Too Low)
  • 3145Terminal 15 ‐ No Signal
  • 3146Water in Fuel Detected or Water in Fuel Circuit Failure
  • 3147Oil Temperature Too High
  • 3148Coolant Temperature Sensor Dynamic Test ‐ Failure (Minimum Temperature Raise Not Reached)
  • 3149Coolant Temperature Sensor Test ‐ Failure (Minimum Temperature Not Reached)
  • 3150System/Amber Warning Lamp – Short Circuit To Battery
  • 3151System/Amber Warning Lamp – Short Circuit To Ground
  • 3152System/Amber Warning Lamp ‐ No Load
  • 3153System/Amber Warning Lamp ‐ Excessive Temperature
  • 3154Grid Heater Relay – Short Circuit To Battery
  • 3155Grid Heater Relay – Short Circuit To Ground
  • 3156Grid Heater Relay ‐ No Load
  • 3157Engine Control Unit (ECU) Not Detected On The CANbus Or The Engine Dataset Registration Information Was Not Available From The Engine Within The Time Required
  • 3158Invalid ECM Checksum (The Engine Dataset Does Not Match The Dataset Registered For This Machine. Register The New Dataset If The Dataset Has Just Been Updated)
  • 3159Invalid Engine Reference Torque
  • 3160Fan Actuator – Short Circuit To Battery
  • 3162Fan Actuator ‐ Open Load
  • 3163Fan Actuator ‐ Temperature Too High
  • 3164Fan Speed Sensor – Signal High
  • 3165Fan Speed Sensor ‐ Signal Low
  • 3166Fuel Filter Heater Relay – Short Circuit To Battery
  • 3167Fuel Filter Heater Relay - Short Circuit To Ground
  • 3168Fuel Filter Heater Relay ‐ Open Load
  • 3169Fuel Filter Heater Relay - Signal Not Plausible
  • 3170NH3 Sensor Value Not Mounted In Proper Position
  • 3172Engine Coolant Temperature Has Exceeded The Pre-Warning Threshold
  • 3173Engine Coolant Temperature Has Exceeded The Warning Threshold
  • 3176High Pressure Pump Fuel Delivery Quantity in Over Run Exceeds a Maximum Threshold
  • 3177Overspeed Detection In Component Engine Protection
  • 3178Timeout Of CAN Message BC2EDC1
  • 3179CAN Communication Failure Between Vehicle Controller and ECU - BC2ECU2 Message
  • 3180CAN Communication Error Between Vehicle Control Module To EDC
  • 3181Rail Pressure Positive Deviation Too High Concerning Set Point
  • 3182Timeout Of CAN Message RxCCVS
  • 3183Timeout Of CAN Message TSC1 ‐ VR (When Active)
  • 3184Timeout Of CAN Message TSC1 ‐ VR (When Inactive)
  • 3185Timeout Of CAN Message TF
  • 3186Cylinder 1 Warning ‐ Fast Decay Error
  • 3187Cylinder 1 Warning ‐ Application Dependent
  • 3188Open Load Error Of An Cylinder 1 (Firing Order)
  • 3189Cylinder 1 Warning ‐ Current Level Error
  • 3190Cylinder 2 Warning ‐ Fast Decay Error
  • 3191Cylinder 2 Warning ‐ Application Dependent
  • 3192Open Load Error Of A Cylinder 4 (Firing Order)
  • 3193Cylinder 2 Warning ‐ Current Level Error
  • 3194Cylinder 3 Warning ‐ Fast Decay Error
  • 3195Cylinder 3 Warning ‐ Application Dependent
  • 3196Open Load Error of Injector in Cylinder 3
  • 3197Cylinder 3 Warning ‐ Current Level Error
  • 3198Cylinder 4 Warning ‐ Fast Decay Error
  • 3199Cylinder 4 Warning ‐ Application Dependent
  • 319CExhaust Flap Sticking or Internal Failure
  • 319C-0Exhaust Flap Actuator
  • 319C-1FExhaust Flap Actuator
  • 319EDownstream NOx Sensor Values Are Not Plausible
  • 319E-0NOx Sensor (CAN)
Looking for a different FPT code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Fault code lists by brand