HeavyEquipmentFix
Ask

New Holland Tractor Fault Codes List: 3158 to 3313

Page 19 of 35 of the full New Holland Tractor fault code list (3,475 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.

New Holland Tractor codes 3158 to 3313

  • 3158lnvalid ECM Checksum (the Engine Dataset Does Not Match the Dataset Registered for this Machine/Register the New Dataset if the Dataset has Just Been Updated)
  • 3159CAN Messages Not Received from Engine Controller
  • 3160Fan Actuator - Short Circuit to Battery
  • 3161Fan Actuator - Short Circuit to Ground
  • 3162Fan Actuator - Temperature Too High
  • 3163Fan Actuator - No Load
  • 3164Fan Speed Above Maximum Threshold
  • 3166Fuel Filter Heater Actuator is Shorted to Battery Voltage
  • 3167Fuel Filter Heater Relay - Short Circuit to Ground
  • 3168Fuel Filter Heater Actuator Has an Open Load Error
  • 3169Fuel Filter Heater ECU Driver Has an Over Temperature Error
  • 3170NH3 Sensor Value Not Mounted in Proper Position
  • 3172Engine Coolant Temperature Has Exceeded the Pre-Warning Threshold
  • 3173Engine Coolant Temperature Has Exceeded the Warning Threshold
  • 3176High Pressure Pump Solenoid Valve - Fuel Delivery Quantity Too High in Overrun Mode
  • 3177Overspeed Detection in Component Engine Protection
  • 3179Can Communication Failure Between Vehicle Controller and ECU - BC2ECU2 Message
  • 3180Can Communication Error Between Vehicle Control Module to EDC
  • 3182CAN Timeout Error From Cruise Control Vehicle Speed (CCVS)
  • 3183CAN Communication Failure Between Vehicle Controller and ECU Controller - TSC1_VR Message (Engine Brake)
  • 3184CAN Communication Failure Between Vehicle Controller and ECU Controller - TSC1_VR Message (Engine Brake)
  • 3185CAN Timeout Error From Transmission - Transmission Fluids (TF) Message
  • 3188Open Load Error of an Cylinder 1 (Firing Order)
  • 3192Open Load Error of an Cylinder 4 (Firing Order)
  • 3196Open Load Error of Injector in Cylinder 3
  • 319CExhaust Flap Sticking or Internal Failure
  • 319EDownstream NOx Sensor Values are Not Plausible
  • 31B6Reporting Error if Relay is Stuck at Closed Position
  • 32Ground Speed Failure, Value Received from Data Bus Indicates Failure Condition
  • 3200Open Load Error of an Cylinder 3 (Firing Order)
  • 3204Open Load Error of Injector in Cylinder 5
  • 3208Open Load Error of an Cylinder 2 (Firing Order)
  • 3210Injection Bank 1 Short Circuit Failure (All Injectors of the Same Bank Can be Affected)
  • 3211Bank 1 - Injection Cable Short Circuit Low Side to Ground
  • 3213lnjection Bank 1 - Unclassifiable Error
  • 3218Injection Bank 2 Short Circuit Failure (All Injectors of the Same Bank Can be Affected)
  • 3219Bank 2 - Injection Cable Short Circuit Low Side to Ground
  • 3221Injection Bank 2 - Unclassifiable Error
  • 3226CAN Timeout Error From eVGT Actuator
  • 3227Injection Processor (CY33X) Error - Internal Reset/Clock Loss/Voltage Too Low
  • 3228Injection Processor (CY33X) Error - Unlocked/Initialization Failure
  • 3229Injection Processor (CY33X) Error - Injections Limited by Software
  • 3230Injection Processor (CY33X) Error - SPI Communication Failure
  • 3231Injection Processor Error - Internal Reset/Clock Loss/Voltage Too Low
  • 3232lnjection Processor Error - Unlocked/Initialization Failure
  • 3233ECU Internal Failure - Internal SPI Injector Related Timeout Error
  • 3234lnjection Processor Error - SPI Communication Failure
  • 3235Injection Control - Number of Injections Limited by Runtime
  • 3236Number of Injections Limited - by Quantity Balance
  • 3237Number of Desired Injections Exceeds Thresholds
  • 3238ECU Power Stages: Errors of the Power Failure Detection of CY320
  • 3239Engine Controller EEPROM - Read Operation Failure
  • 3240Engine Controller EEPROM - Write Operation Failure
  • 3241ECU Internal Failure - EEPROM Write/Read Error
  • 3242ECU Internal: Visibility of Software Resets in DSM
  • 3243Engine Controller Recovery (Suppressed) - Recovery Occurred
  • 3244Engine Controller Recovery (Visible) - Recovery Occurred
  • 3245Diagnostic Fault Check to Report Errors in Query - Response Communication
  • 3246Shutoff Paths During Initialization - Watchdog
  • 3247Shutoff Paths Failed During Initialization - Supply Voltage too High
  • 3248Shutoff Paths During Initialization - Supply Voltage Too Low
  • 3249TPU Monitoring - Time Deviation Between TPU and System Not Plausible
  • 3250Dataset - Variant Defect
  • 3251Dataset - Requested Variant Could Not Be Set
  • 3252Diagnostic Fault Check to Report Errors in SPI - Communication
  • 3253Analog Digital Converter (ADC): Diagnostic Fault Check to Report the Error in Voltage Ratio in ADC Monitoring
  • 3254ADC Monitoring - Reference Voltage too High
  • 3255Analog Digital Converter (ADC): Diagnostic Fault Check to Report the ADC Test Error
  • 3256Analog Digital Converter (ADC): Diagnostic Fault Check to Report the NTP Error in ADC Monitoring
  • 3258ECU Power Stages: Starter Relay HS Power Stage Output Short Circuit to Battery
  • 3259ECU Power Stages: Starter Relay HS Power Stage Output Short Circuit to Ground
  • 325ADEF Supply Module Pump Temperature is Too Low to Activate Pump
  • 3260Starter Relay Low Side Driver Circuit Open Failure (*)
  • 3261Starter Relay - Short Circuit to Battery at Low Side Power Stage
  • 3262Starter Relay - Short Circuit to Ground at Low Side Power Stage
  • 3263Busoff in CAN C Mapped to Primary Bus
  • 3265Diagnostic Fault Check to Report the Error Due to Over Run
  • 3266Redundant Engine Speed in Overrun Monitoring - Speed Signal Not Plausible
  • 3267Main Relay 3 - Short Circuit to Battery
  • 3268Main Relay 3 - Short Circuit to Ground
  • 3278Engine Controller Supply Voltage too High
  • 3279Engine Controller Internal Supply Voltage too Low
  • 328012V Sensor Supply 1 Voltage is Too High
  • 328112V Sensor Supply 1 Voltage is Too Low
  • 3283ECU Internal Failure - Sensor 5 Volt Supply 2
  • 3284Sensor Supply Voltage 2 - Low
  • 3285ECU Internal Failure - Sensor 5 Volt Supply 3
  • 3286Sensor Supply Voltage 3 - Low
  • 3293Fuel Metering Unit: Maximum Positive Deviation of Rail Pressure Exceeded
  • 3297Rail Pressure Positive Deviation High and High Fuel Flow Setpoint Value
  • 329CExhaust Flap Actuator Supply Voltage Out of Range
  • 32BGlow Plug Control Circuits Shorted to Battery
  • 32B6Reporting Error if Relay is Stuck at Open Position
  • 32BEUpstream NOx Sensor Lambda Signal Deviation NOx Sensor Possible Removal Detected
  • 33The Power Supply of the Electronic Front Hitch (EFH) is Too Low
  • 3301Fuel Metering Unit: Maximum Negative Rail Pressure Deviation with Metering Unit on Lower Limit is Exceeded
  • 3305High Pressure Pump Solenoid Valve - Minimum Rail Pressure Exceeded
  • 3309High Pressure Pump Solenoid Valve - Maximum Rail Pressure Exceeded
  • 3312Compared Camshaft and Crankshaft Speed Sensor Values are Not Plausible
  • 3313Rail Pressure Drop Rate Too High
Looking for a different New Holland Tractor code?Search the full fault-code database, or hand the code to the AI assistant for a plain-English explanation.

Other New Holland machine types

Fault code lists by brand