New Holland Fault Codes List: 3122 to 3229
Page 7 of 15 of the full New Holland fault code list (1,492 codes). Each entry is the code as the machine reports it and what the manufacturer data says it means.
New Holland codes 3122 to 3229
- 3122PTO Twist Sensor – Short Circuit To Ground
- 3123PTO Twist Sensor ‐ Not Calibrated
- 3124Hand Throttle ‐ Channel 2 Above Range Max.
- 3125Hand Throttle ‐ Channel 2 Below Range Min.
- 3126Hand Throttle ‐ Channel 1 Signal Above Range Max.
- 3127Hand Throttle ‐ Channel 1 Signal Below Range Min.
- 3128Hand Throttle ‐ Channel Difference Error
- 3129Hand Throttle ‐ Idle Switch Closed Circuit
- 3130Hand Throttle ‐ Idle Switch Open Circuit
- 3131Grid Heater Always Switched On
- 3133Cold Start Lamp ‐ No Load
- 3134Cold Start Lamp – Short circuit to Battery
- 3135Cold Start Lamp – Short Circuit To Ground
- 3136Cold Start Lamp ‐ Excessive Temperature
- 3137Metering Unit - Open Load
- 3138Metering Unit ‐ Temperature Too High
- 3139Metering Unit Signal Range Check - Signal Too High
- 3140Metering Unit Signal Range Check - Signal Too Low
- 3141Fuel Flow Setpoint Too Low - Fuel Metering Unit: Leakage is Detected Based on Fuel Quantity Balance
- 3142High Pressure Test ‐ Test Active
- 3143Grid Heater Switch Off Test (Voltage Drop Too High)
- 3144Grid Heater Switch Off Test (Voltage Drop Too Low)
- 3145Terminal 15 ‐ No Signal
- 3146Water Detected in Fuel
- 3147Oil Temperature Too High
- 3148Coolant Temperature Sensor Dynamic Test ‐ Failure (Minimum Temperature Raise Not Reached)
- 3149Coolant Temperature Sensor Test ‐ Failure (Minimum Temperature Not Reached)
- 3150System/Amber Warning Lamp – Short Circuit To Battery
- 3151System/Amber Warning Lamp – Short Circuit To Ground
- 3152System/Amber Warning Lamp ‐ No Load
- 3153System/Amber Warning Lamp ‐ Excessive Temperature
- 3154Grid Heater Relay – Short Circuit To Battery
- 3155Grid Heater Relay – Short Circuit To Ground
- 3156Grid Heater Relay ‐ No Load
- 3157Engine Control Unit (ECU) Not Detected on the CAN Bus or the Engine Dataset Registration Information was Not Available From the Engine within the Time Required
- 3158Invalid ECM Checksum (The Engine Dataset Does Not Match the Dataset Registered for This Machine. Register the New Dataset if the Dataset Has Just Been Updated)
- 3159Invalid Engine Reference Torque
- 3160Fan Actuator – Short Circuit To Battery
- 3162Fan Actuator ‐ Open Load
- 3163Fan Actuator ‐ Temperature Too High
- 3164Fan Speed Sensor – Signal High
- 3165Fan Speed Sensor ‐ Signal Low
- 3166Fuel Filter Heater Relay – Short Circuit To Battery
- 3167Fuel FiIter Heater Relay - Short Circuit to Ground
- 3168Fuel Filter Heater Relay ‐ Open Load
- 3169Fuel FiIter Heater Relay - Signal Not Plausible
- 3176Fuel Metering Unit: Set Point of Metering Unit in Overrun Mode Not Plausible
- 3177Engine Over Speed Detected
- 3178Timeout Of CAN Message BC2EDC1
- 3179Timeout of CAN Message BC2EDC2
- 3180Timeout of CAN Message VCM2EDC
- 3181Rail Pressure Positive Deviation Too High Concerning Set Point
- 3182Timeout Of CAN Message RxCCVS
- 3183Timeout Of CAN Message TSC1 ‐ VR (When Active)
- 3184Timeout Of CAN Message TSC1 ‐ VR (When Inactive)
- 3185Timeout Of CAN Message TF
- 3186Cylinder 1 Warning ‐ Fast Decay Error
- 3187Cylinder 1 Warning ‐ Application Dependent
- 3188Cylinder 1 Warning ‐ Injector Circuit Low
- 3189Cylinder 1 Warning ‐ Current Level Error
- 3190Cylinder 2 Warning ‐ Fast Decay Error
- 3191Cylinder 2 Warning ‐ Application Dependent
- 3192Injector Cylinder 2 Warning - Open Load
- 3193Cylinder 2 Warning ‐ Current Level Error
- 3194Cylinder 3 Warning ‐ Fast Decay Error
- 3195Cylinder 3 Warning ‐ Application Dependent
- 3196Injector Cylinder 3 Warning - Open Load
- 3197Cylinder 3 Warning ‐ Current Level Error
- 3198Cylinder 4 Warning ‐ Fast Decay Error
- 3199Cylinder 4 Warning ‐ Application Dependent
- 3200Injector Cylinder 4 Warning - Open Load
- 3201Cylinder 4 Warning ‐ Current Level Error
- 3202Cylinder 5 Warning ‐ Fast Decay Error
- 3203Cylinder 5 Warning ‐ Application Dependent
- 3204Cylinder 5 Warning ‐ Open Load
- 3205Cylinder 5 Warning ‐ Current Level Error
- 3206Cylinder 6 Warning ‐ Fast Decay Error
- 3207Cylinder 6 Warning ‐ Application Dependent
- 3208Cylinder 6 Warning ‐ Open Load
- 3209Cylinder 6 Warning ‐ Current Level Error
- 3210Bank 1 ‐ General Short Circuit On Injection Cable
- 3211Bank 1 ‐ Injection Cable Short Circuit Low Side To Ground
- 3212Bank 1 ‐ Application Dependent
- 3213Bank 1 ‐ Unclassifiable Error
- 3214Bank 1 Warning ‐ Application Dependent
- 3215Bank 1 Warning ‐ Application Dependent
- 3216Bank 1 Warning ‐ Open Load
- 3217Bank 1 Warning ‐ Unclassifiable Error
- 3218Bank 2 - General Short Circuit on Injection Cable
- 3219Bank 2 ‐ Injection Cable Short Circuit Low Side To Ground
- 3220Bank 2 ‐ Application Dependent
- 3221Bank 2 ‐ Unclassifiable Error
- 3222Bank 2 Warning ‐ Application Dependent
- 3223Bank 2 Warning ‐ Application Dependent
- 3224Bank 2 Warning ‐ Open Load
- 3225Bank 2 Warning ‐ Unclassifiable Error
- 3226Messages SRA2EDC
- 3227Injection Processor (CY33X) Error ‐ Internal Reset / Clock Loss / Voltage Too Low
- 3228Injection Processor (CY33X) Error ‐ Unlocked / Initialization Failure
- 3229Injection Processor (CY33X) Error ‐ Injections Limited By Software
Other New Holland machine types
Fault code lists by brand
- CAT8,286 codes
- Volvo6,508 codes
- FPT3,033 codes
- Case IH2,992 codes
- Bobcat2,653 codes
- Challenger Tractor2,434 codes
- John Deere Tractors1,884 codes
- Case Wheel Loader1,859 codes
- John Deere Engines1,853 codes
- Cummins1,847 codes
- Challenger Rubber Track Tractor1,747 codes
- Volvo Wheel Loader1,726 codes
- Deutz1,684 codes
- Perkins1,523 codes
Safety-critical: confirm before use
Safety first: park on level ground, stop the engine, and secure the machine before any inspection. Thresholds, component locations, wire numbers, fuse locations, and reset procedures can vary by model, configuration, and serial number. Confirm them in the service documentation for your exact machine.